. Strain energy of the stretched wire is 18 × 10-³ J and strain energy per unit volume of the same wire under same conditions is 6 × 10-³ J/m³. Find its volume.
Q: 1. A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by a uniaxial tensile…
A: Given: Steel rod diameter, D= 3.2 mm Tensile load, F = 4800 N'
Q: A structural steel rod has a radius of 10mm and length of 1.0m. A 100kN force stretches it along its…
A: Write the expression for stress.
Q: our biceps muscle is attached to your elbow by the distal biceps tendon. An average adults tendon…
A:
Q: A load 1 kg produces a certain extension in the wire of length 3 m and radius 5 x 10-4 m. How much…
A: To find- Lateral strain=? Given- Load (M)=1 kgLength of wire (L)=3 mRadius (r)=5×10-4mYoung's…
Q: a circular coil of wire has 21 turns and a radius of 0.35 m. If it is immersed within a uniform…
A: The radius of the circular coil R=0.35 m. Number of turns N=21. The magnitude of the uniform…
Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…
A:
Q: modulus (Y) and energy density (E). The strain A stretching wire has a Young's in a stretching wire…
A: To find-Strain in wire=?Given-Young's modulus=YEnergy density=E
Q: The yield strength of a person’s ACL is approximately 3.5x10^7 N/m^2. What is this persons Modulus…
A:
Q: A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on its narrow…
A:
Q: Two wires have lengths in the ratio 4 : 3 diameters in the ratio 2 : 1. Calculate elongations…
A: To find-Ratio of elongations x1 : x2Given data-Y1 : Y2=1 : 2,L1 : L2=4 : 3d1 : d2=2 : 1
Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…
A: stress is defined as the force per unit area. Write the expression for stress. S=FA…
Q: The maximum compressional stress that a bone can withstand is 1.6 × 108 N/m2 before it breaks. A…
A:
Q: A copper wire of length 6.7 m , cross sectional area 3.2 x 10--m²and Young's modulus 11 x 1010 N/m²…
A: Length of wire L = 6.7 m Cross-sectional area A = 3.2 × 10- 6 m2 Young modulus Y = 11 × 1010 N/m2…
Q: A 50-N force is applied to a metal rod with a length of 10 m and a cross- sectional area of 1.0 x…
A:
Q: A wire of uniform cross sectional area of 0.15 mm2 is stretched at both ends by a total force of 40…
A: Given, Area of cross section of the wire A = 0.15 mm2 Total force acting on the both end F = 40 N…
Q: I have a square box with a notch in the center, this one has two modes: 0 and 45 degree angle. A…
A:
Q: 0.02 1 1.4 0.5 0.04 2 2.8 1 0.06 3 4.2 1.5 0.08 4 5.6 2 0.1 5 7 2.5
A: Solution:
Q: • A steel wire of diameter 1 x 10³ m is stretched by a force of 20 N. Calculate the. strain energy…
A: We need to compute-Strain energy per unit volume=?The data given as-Diameter of wire (d)=10-3 mForce…
Q: A punch for making holes in steel plates is shown in Fig. below. Assume that a punch having diameter…
A: Hence the answer..
Q: The figure shows the stress versus strain plot for an aluminum wire that is stretched by a machine…
A:
Q: To escape a burning buildingAmold has to jump from a third-story window that is about 10.0 m above…
A:
Q: I the stress experience when deformation is caused by tangential forces to the surface * O Inertia O…
A: The stress experienced when force is applied perpendicular to surface is called compressive stress .
Q: When a beam 6m. long with a cross sectional area 0f 19.4 square meters is subjected to a…
A: Young’s modulus (Y) = stress/strain = (F/A)/(ΔL/ L0). Where, F is the force exerted on an object…
Q: A 7-kip · ft torque is applied to a hollow aluminum shaft having the cross section shown. Neglecting…
A: Given data- T=7 kip-ft Radius of outer circle, r0=7 in Radius of inner circle, ri=14 in-4 in-2 in2=4…
Q: The young modulus of a material whose elastic strain and stress are 1.53 and 169.42 N/m²…
A: The elastic strain, strain=1.53 The stress, stress=169.42 N/m2
Q: Tensile load of 2 MN is applied to an Aluminium cord with original diameter of 5 mm, the measured…
A: Given data: Magnitude of tensile load is, F=2 MN=2×106 N Original diameter of Aluminum cord is, d=5…
Q: Proof that the energy stored in the compact bone is given by E = AL0 (Sb) ^ 2 / 2γ. When Sb is bone…
A:
Q: A solid rod with cross section area A= 1.8 cm2 and length LO =16 cm, performed tensile test as shown…
A: Given data: Area of cross-section of rod is, A=1.8 cm2. Length of rod is, L0=16 cm.
Q: Derive an expression for elastic potential energy of wire under stress.
A: Write the mathematical expression for Hook’s law.
Q: 5 Jlgul Compressive strain is the ratio between decrease in length and original length ylgn O ihi O
A: Compressive strain = -∆Lo/L Here, -∆Lo denotes decrease in length and L is the original length.…
Q: Q. 8: Strain energy per unit volume is given by 1 (stress)? 1 (b) 2 * (stress)* y (a) 2 y 1 strain 1…
A: We know, Strain is produced in the wire due to application of load. Hence. work is done on…
Step by step
Solved in 2 steps