6. In class we mentioned the idea of internal resistance of a battery. Ideally, for a perfectbattery one would have AV = E, the electromotive force. In reality, every battery havea small but nonzero internal resistance r which means the actual potential differenceacross the battery is not constant, and may sometimes be significantly different thanwhat it is rated for.and the current is given byWM|1|*3(a) Show that the potential difference across the battery isAV = E - ir=`loadi =Er+Rload(b) If r = 10, plot AV versus Rload-(c) Given the above, explain why sometimes we don't care about the internal resis-tance.(d) Let E1.53V, and the measured voltage and current across a 15.60 load isrespectively 1.49V and 96mA, what is the internal resistance?

Answered: Image /qna-images/answer/7311f4c8-488f-48d8-a2e8-bc47c96114d4.jpg

. In class we mentioned the idea of internal resistance of a battery. Ideally, for a perfect battery one would have AV = E, the electromotive force. In reality, every battery have a small but nonzero internal resistance r which means the actual potential difference across the battery is not constant, and may sometimes be significantly different than what it is rated for. ^^^||1|* and the current is given by 3 {R (a) Show that the potential difference across the battery is AV = E-ir i = load E r+Rload (b) If r = 10, plot AV versus Rload- (c) Given the above, explain why sometimes we don't care about the internal resis- tance. (d) Let & = 1.53V, and the measured voltage and current across a 15.60 load is respectively 1.49V and 96mA, what is the internal resistance?

. In class we mentioned the idea of internal resistance of a battery. Ideally, for a perfect battery one would have AV = E, the electromotive force. In reality, every battery have a small but nonzero internal resistance r which means the actual potential difference across the battery is not constant, and may sometimes be significantly different than what it is rated for. ^^^||1|* and the current is given by 3 {R (a) Show that the potential difference across the battery is AV = E-ir i = load E r+Rload (b) If r = 10, plot AV versus Rload- (c) Given the above, explain why sometimes we don't care about the internal resis- tance. (d) Let & = 1.53V, and the measured voltage and current across a 15.60 load is respectively 1.49V and 96mA, what is the internal resistance?

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Wire C and wire D are made from different materials and have length Lc = Lp = 2.4 m. The resistivity and diameter of wire C are 5.0 × 10-6 Q.m and 1.32 mm, and those of wire D are 1.2 × 106 Q2•m and 0.79 mm. The wires are joined as shown in the figure and a current of 4.9 A is set up in them. What is the electric potential difference between (a) points 1 and 2 and (b) points 2 and 3? What is the rate at which energy is dissipated between (c) points 1 and 2 and (d) points 2 and 3? C ·Lc (a) Number i 4.3e-5 Units V (b) Number 2.9E-5 Units V (c) Number i 2.1e-4 Units W 2 (d) Number i 1.4e-4 Units W D -LD 3
Help
(a) Consider the circuit below. Point b is grounded(potential=0). Determine the potential at a.(b) Two resistors of cylindrical shape ,A &B, made from same material. Length of resistor A is twice that of resistor B. The diameter of B is half that of A. Determine the ratio of Resistance ofA/Resistance of B.
I attached the picture of the question, but just in case it is hard to read here it is typed out! Also, I need the answers correct to 4 decimal places. Thank you!! The figure shows how a bleeder resistor is used to discharge a capacitor after an electronic device is shut off, allowing a person to work on the electronics with less risk of shock. The resistor has a resistance of 302 kΩ. a. What is the time constant? (in s) b. How long will it take to reduce the voltage on the capacitor to 1.0% of its full value once discharge begins? (in s) c. If the capacitor is charged to a voltage ?0 through a 120 Ω resistance, calculate the time it takes to rise to 0.9?0 (This is close to two time constants.) (in ms)
please exaplain me step by step and clear hand wrriting please