.) Determine the Moment Inertia about the Centroidal Y-Axis (Iy) 12.) Determine the Polar Moment of Inertia about Centroidal Axes. 13.) Determine the Moment Inertia about the x-axis. 14.) Determine the Moment about the y-axis.

.) Determine the Moment Inertia about the Centroidal Y-Axis (Iy) 12.) Determine the Polar Moment of Inertia about Centroidal Axes. 13.) Determine the Moment Inertia about the x-axis. 14.) Determine the Moment about the y-axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the reaction at the roller support. Ans.: Blank 1 N Determine the moment reaction at the fixed support Ans.: Blank 1 N.m Determine the angle of rotation at the roller support.Ans.: E I delta = Blank 1 N.m3 Determine the deflection at 2 meters from the roller support along the beam. Ans.: E I delta = Blank 1 N.m3
The lamp has a weight of 0.20 kN and is supported by a pole AO and cables AB and AC. If the force in the pole acts along its axis, determine the forces in AO, AB, and AC for equilibrium.
Problem 6 Using the Muller-Breslau's Principle, draw the influence lines of the following response functions for the beam shown below. 1) Vertical reactions at supports A, B, and F 2) The end moment at point F 3) Shear to the left of support B 4) Shear at E Á B ₁8m- hinge (E) n ————▬▬▬▬4 m-√— 4 m▬-|-—+m−|4m| F
Q3/I A) Find the reactions at point O? B) Calculate the moment of the 250 N force about the base point O of the robot. 20° 400 mm 250 N 500 mm 300 mm اضف ملف
11.7 Problems for Solution Section 11.1 For Problems 11.1 through 11.16, compute the reactions for the beams and frames. E and I are constant unless noted otherwise. The force method (i.e., method of consistent distortions) is to be used. De Onload D n *** -)
A counterclockwise moment of 2.5 kNm must be created about point A in order to raise the lamp post from the position shown. Neglect mass of the pole. The lamp at point D has a mass of 5kg. If the value of force, F= 1.5 kN, determine the distance from point E to point D given that distance ED=2EB. Note: EA is perpendicular to ED.
Find the location and the intensity of the maximum positive moment from the left end of the beam shown. 10 kN/m 50 kN A В 5 m 5 m 5 m 5 m
QUESTION 6 Point A is constrained to move horizontally and is moving to the right at a speed of 5 m/s. The rack B engages with the circular gear which spins about 0. Determine the following: (a) The angular velocity of the gear (b) The angular velocity of link AB B A 200 mm 5 m/s 400 mm
*21-16. The bent rod has a mass of 3 kg/m. Determine the moment of inertia of the rod about the O-a axis. 0.3 m 1 m O 0.5 m y
MECHANISM F= MA In the link (10 kg) below at time 0 seconds, the rotational velocity of the link is zero and theta is o degrees. A constant torque of 5 N-m is applied to the link. The system is horizontal so gravity can be ignored. 1. Determine the angular velocity after it has made 3 revolutions and is again at 0 degrees. 2. What is the magnitude of the force in the radial direction on the pin joint when the link has completed 3 revolutions? 5 N-m 0.5 m
Influence Lines of Beam: For questions Q1 and Q2, draw the influence lines for the vertical reaction at D and the moment at C of the given beam. The modulus of elasticity is constant. 21 20ft 10ft 20ft B Q1: What is the maximum ordinate of the vertical reaction at D is given? A. 1.10 В. 1.00 C.0.865 D. 0.679 Q2: Write the maximum ordinate of the influence line of the moment at C in the space below.
Q3: The of the moments about point A due to the forces and couples acting on the bar is sum zero, (a) What is the magnitude of the couple C?. (b) Determine the sum of the moments about point В. Ans. C = 26.0 kN.m, MB =0.0 B. 4 kN 3m 20 KN-m 4KN 5KN 3 KN -5 m- -3m-