EP ENGR.MECH.-MOD.MASTERING ACCESS
EP ENGR.MECH.-MOD.MASTERING ACCESS
15th Edition
ISBN: 9780134867267
Author: HIBBELER
Publisher: PEARSON CO
bartleby

Concept explainers

bartleby

Videos

Textbook Question
Book Icon
Chapter 8, Problem 1FP

F8–1. Determine the friction developed between the 50-kg crate and the ground if a) P=200 N, and b) P=400 N. The coefficients of static and kinetic friction between the crate and the ground are, μs = 0.3 and, μk = 0.2.

Chapter 8, Problem 1FP, F81. Determine the friction developed between the 50-kg crate and the ground if a) P=200 N, and b)

(a)

Expert Solution
Check Mark
To determine

The frictional force (F).

Answer to Problem 1FP

(a) The frictional force (F) is 160N_ .

(b) The frictional force (F) is 146N_ .

Explanation of Solution

Given:

The mass of the crate (m) is 50 kg.

The co-efficient of static friction (μs) is 0.3.

The co-efficient of kinetic friction (μk) is 0.2.

Show the free body diagram of the crate as in Figure (1).

EP ENGR.MECH.-MOD.MASTERING ACCESS, Chapter 8, Problem 1FP , additional homework tip  1

Using Figure (1),

Determine the normal reaction (N) using the equation of equilibrium.

Along the vertical direction:

Fy=0NWP×(35)=0NmgP×(35)=0 (I)

Here, the acceleration due to gravity is g.

Determine the frictional force using the equation of equilibrium.

Along the horizontal direction:

Fx=0FP(45)=0 (II)

Conclusion:

Substitute 50 kg for m, 9.81m/sec2 for g, and 200 N for P in Equation (I).

N50×9.81200×(35)=0N=610.5N

Substitute 200 N for P in Equation (II).

F200×(45)=0F=160N

Check:

Determine the maximum frictional force.

Fmax=μsN

Substitute 0.3 for μs and 610.5 N for N.

Fmax=0.3×610.5=183.15N

The maximum frictional force (183.15 N) is greater than the frictional force (160 N); therefore the block will not slip.

Therefore, the frictional force is 160N_ .

(b)

Expert Solution
Check Mark
To determine

The frictional force (F).

Answer to Problem 1FP

The frictional force (F) is 146N_ .

Explanation of Solution

Given:

The mass of the crate (m) is 50 kg.

The co-efficient of static friction (μs) is 0.3.

The co-efficient of kinetic friction (μk) is 0.2.

Show the free body diagram of the crate as in Figure (2).

EP ENGR.MECH.-MOD.MASTERING ACCESS, Chapter 8, Problem 1FP , additional homework tip  2

Using Figure (2),

Determine the normal reaction (N) using the equation of equilibrium.

Along the vertical direction:

Fy=0NWP×(35)=0NmgP×(35)=0 (III)

Determine the frictional force using the equation of equilibrium.

Along the horizontal direction:

Fx=0FP(45)=0 (IV)

Conclusion:

Substitute 50 kg for m, 9.81m/sec2 for g, and 400 N for P in Equation (III).

N50×9.81400×(35)=0N=730.5N

Substitute 400 N for P in Equation (IV).

F400×(45)=0F=320N

Check:

Determine the maximum frictional force.

Fmax=μsN

Substitute 0.3 for μs and 730.5 N for N.

Fmax=0.3×730.5=219.15N

The maximum frictional force (219.15 N) is less than the frictional force (320 N); therefore the block will slip. Hence, find the frictional force using the co-efficient of kinetic friction.

Find the frictional force using the relation.

F=μkN

Substitute 0.2 for μk and 730.5 N for N.

F=0.2×730.5=146N

Thus, the frictional force is 146N_ .

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!
Students have asked these similar questions
Please stop screenshoting ai solution,it always in accurate solve normal
Research and select any different values for the Ratio of connecting rod length to crank radius from various engine models, then analyze how these changes affect instantaneous velocity and acceleration, presenting your findings visually using graphs.
Pb 9) 4.44 bas gnibus& WX 002 grillimatul fred bail (e) For the simply supported I-beam, a load of 1000 lb in center. Find the maximum transverse shear stress. Compare your answer with the approximation obtained by dividing the shear load by the area of the web only with the web considered to extend for the full 8-in depth. - 3½ in. 12 bas in 0% to tolerabib tormi no grived in. 8 in. 38 in. 12 ½ in.

Chapter 8 Solutions

EP ENGR.MECH.-MOD.MASTERING ACCESS

Ch. 8 - The mine car and its contents have a total mass of...Ch. 8 - Prob. 4PCh. 8 - The automobile has a mass of 2 Mg and center of...Ch. 8 - The automobile has a mass of 2 Mg and canter of...Ch. 8 - Prob. 9PCh. 8 - Determine the angle at which the applied force P...Ch. 8 - Prob. 12PCh. 8 - The car has a mass of 1.6 Mg and center of mass at...Ch. 8 - The log has a coefficient of state friction of, s...Ch. 8 - The spool of wire having a weight of 300 Ib rests...Ch. 8 - The spool of wire having a weight of 300 Ib rests...Ch. 8 - Prob. 20PCh. 8 - The uniform thin pole has a weight of 30 Ib and a...Ch. 8 - The uniform pole has a weight of 30 Ib and a...Ch. 8 - The friction pawl is pinned at A and rests against...Ch. 8 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8 - Two blocks A and B have a weight of 10 Ib and 6...Ch. 8 - Determine the smallest force P that must be...Ch. 8 - The man having a weight of 200 Ib pushes...Ch. 8 - The uniform hoop of weight W is subjected to the...Ch. 8 - Determine the maximum horizontal force P that can...Ch. 8 - Determine the minimum force P needed to push the...Ch. 8 - Prob. 41PCh. 8 - Prob. 42PCh. 8 - Prob. 51PCh. 8 - Prob. 52PCh. 8 - Determine the smallest couple moment that can be...Ch. 8 - If P=250 N, determine the required minimum...Ch. 8 - Determine the minimum applied force P required to...Ch. 8 - Prob. 67PCh. 8 - Prob. 68PCh. 8 - Prob. 71PCh. 8 - Prob. 72PCh. 8 - Prob. 73PCh. 8 - Prob. 74PCh. 8 - Prob. 81PCh. 8 - Determine the horizontal force P that must be...Ch. 8 - A 180-lb farmer tries to restrain the cow from...Ch. 8 - The 100-lb boy at A is suspended from the cable...Ch. 8 - Prob. 87PCh. 8 - Determine the force P that must be applied to the...Ch. 8 - Prob. 93PCh. 8 - Prob. 98PCh. 8 - Prob. 99PCh. 8 - Blocks A and B have a mass of 7 kg and 10 kg,...Ch. 8 - The uniform bar AB is supported by a rope that...Ch. 8 - Prob. 102PCh. 8 - A 10-kg cylinder D, which is attached to a small...Ch. 8 - Prob. 106PCh. 8 - The collar bearing uniformly supports an axial...Ch. 8 - The collar bearing uniformly supports an axial...Ch. 8 - The floor-polishing machine rotates at a constant...Ch. 8 - Prob. 110PCh. 8 - Prob. 111PCh. 8 - Prob. 116PCh. 8 - The collar fits loosely around a fixed shaft that...Ch. 8 - Prob. 119PCh. 8 - Prob. 120PCh. 8 - Solve Prob. 8-120 if the force P is applied...Ch. 8 - Prob. 122PCh. 8 - Prob. 123PCh. 8 - Prob. 125PCh. 8 - The bell crank fits loosely into a 0.5-in-diameter...Ch. 8 - The bell crank fits loosely into a 0.5-in-diameter...Ch. 8 - Prob. 129PCh. 8 - R81. The uniform 20-lb ladder rests on the rough...Ch. 8 - R82. The uniform 60-kg crate C rests uniformly on...Ch. 8 - R83. A 35-kg disk rests on an inclined surface for...Ch. 8 - Prob. 4RPCh. 8 - Prob. 6RPCh. 8 - Prob. 7RPCh. 8 - The hand cart has wheels with a diameter of 80 mm....
Knowledge Booster
Background pattern image
Mechanical Engineering
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.
Similar questions
SEE MORE QUESTIONS
Recommended textbooks for you
Text book image
International Edition---engineering Mechanics: St...
Mechanical Engineering
ISBN:9781305501607
Author:Andrew Pytel And Jaan Kiusalaas
Publisher:CENGAGE L
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License