Chapter 5, Problem 5.30P

not use ai please

Procedure:- 1- Connect the cct. shown in fig.(2). a ADDS DS Fig.(2) 2-For resistive load, measure le output voltage by using oscilloscope ;then sketch this wave. 3- Measure the average values ::f VL and IL: 4- Repeat steps 2 & 3 but for RL load. Report:- 1- Calculate the D.C. output vcl age theoretically and compare it with the test value. 2- Calculate the harmonic cont :nts of the load voltage, and explain how filter components may be selected. 3- Compare between the three-phase half & full-wave uncontrolled bridge rectifier. 4- Draw the waveform for the c:t. shown in fig.(2) but after replaced Di and D3 by thyristors with a 30° and a2 = 90° 5- Draw the waveform for the cct. shown in fig.(2) but after replace the 6-diodes by 6- thyristor. 6- Discuss your results. Please solve No. 4 and 5

a.) Sketch each of the following signals, and starting with the defining relation, finds its Fourier transform X (w) - a) x(t) = rect(t − 3) b) x(t)=3t rect(t) c) x(t) = 2te 3u1(t) d) x(t) = e−2|t| b.) Sketch the magnitude and phase spectrum for the four signals in Problem (a). c) Calculate energy using time-domain and frequency domain formulas for signals in Problem (a) and (b). Confirm Parseval's theorem using these calculations.

I need help in construct a method in matlab to find the voltage of VR1 to VR4, rhe current, and the power base on that circuit Nominal or Theortical: E1 = 3V , E2 = 9V, E3 = 1.5V R1 =10Kohm, R2 =2Kohm, R3 =1Kohm, R4 =16Kohm

I have a question based on the mesh anaylsis, why does current around R1 and the same as R3?

1. Compute the output signals S and T for the circuit. Input signals P = 1, Q = 1, and R = 1. C₁ P half-adder #1 R AND -S C₁₂ half-adder #2 2. Use 8-bit representations to compute the following sum. Show all work. 57+(-118) 3. Find a counterexample to show that the following statement is false: 1 Vx Є R, x>- χ T 4. Is the proposed negation correct? If yes, provide a sound reasoning. If not, provide a sound reasoning and write the correct negation. Statement: For all integers n, if n² is even then n is even. Negation: For all integers n, if n² is even then n is not even.

not use ai

2. (35 points) Use you program to investigative properties of a four step linear pathway. Just extend the model given in question 1 to include an additional two species x2 and x3. You can assume simple irreversible mass-action kinetic on each reaction. I recommend you use the following values for the rate constants: 1 = 0.6; k2 = 1.8; k3 = 0.5; k40.04. This will enable you to more easily answer the following questions. You can also assume that the input is the source X and you can set its value to one. You may find that the plot of the phase change at x3 is broken at -180 degrees because it wraps around. To avoid this you can use the method: phase = np.unwrap(phase) to make sure the phase plot is continuous. [10] i) Compute and show the Bode plots for x1, x2 and x3 with respect to the input Xo. [5] ii) Do you see a pattern with the maximum phase shifts as you move from x₁ to x3? [10] iii) Can you explain this pattern? [5] iv) What would you predict would be the maximum phase shift for…

Please answer all The zombies showed up while you were sleeping!  The zombie alarm you built goes off as they open the door.  You jolt awake to see an alpha-zombie charging through the door.  The alphas are zombies that turned all of the zombies in its army.  If you can take down this one zombie, all the others pouring into the room should fall as well.  Luckily, your group was prepared for this eventuality.  Another member of your team has constructed the zombie shocker circuit shown in Figure 5, using some batteries for the voltage source, some rusty metal for the resistors and a coil of wire for the inductor.  The switch is just you pulling apart two wires to open the circuit (while holding them by their insulated sheaths).   1. Construct the circuit shown in Figure 15 in the Circuit JS simulator.   2. Start the simulation with switch SW1 in the closed position.  You’ve been charging this circuit all night, so you’ll want to let the circuit run for a while (roughly 30 seconds at max…