Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.

Question

Want to see more full solutions like this?

Answer 1

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

2 A metal block of mass m = 10 kg is sliding along a frictionless surface with an initial speed Vo, as indicated below. The block then slides above an electromagnetic brake that applies a force FEB to the block, opposing its motion. The magnitude of the electromagnetic force varies quadratically with the distance moved along the brake (x): 10 FEB = kx², with k = 5 N m² V₁ = 8 m/s m = 10 kg FEB Frictionless surface Electromagnetic brake ⇒x Determine how far the block slides along the electromagnetic brake before stopping, in m.

Q1: Determine the length, angle of contact, and width of a 9.75 mm thick leather belt required to transmit 15 kW from a motor running at 900 r.p.m. The diameter of the driving pulley of the motor is 300 mm. The driven pulley runs at 300 r.p.m. and the distance between the centers of two pulleys is 3 meters. The density of the leather is 1000 kg/m³. The maximum allowable stress in the leather is 2.5 MPa. The coefficient of friction between the leather and pulley is 0.3. Assume open belt drive.

5. A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa. [Ans. m = 6 mm; b= 60 mm; Tp=24; T=96; Dp = 144mm; DG = 576 mm]

Answer 2

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Textbook Question

Chapter 41, Problem 1RQ

Before installing a gauge on the high-pressure side of a system, you should do which of the following?
A. Turn on the system.
B. Turn off the system.
C. Adjust the system to a neutral position.
D. Have a cylinder approved by the DOT nearby.

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Textbook Question

Answer 6

Textbook Question

Answer 7

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 8

Expert Solution & Answer

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

To determine

The work should be done before installing a gauge on the high-pressure side of a system.

Answer 12

Answer to Problem 1RQ

The work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 13

Explanation of Solution

The pressure gauge is an instrument used to measure the gauge pressure of the flow of fluid. It displays high and low pressure side of the system when it is put in operation. This used to convert the pressure of the system different refrigerant requirements.

The technician should be skilled to attach the manifold gauge. Attaching the gauge to the manifold should be done very carefully. Wearing goggles and gloves are necessary while attaching the gauge otherwise the high-pressurised refrigerant can injure to eyes and skin of technician.

This type of dangerous condition can be prevented by letting the pressure of high-pressure side refrigerant down to lower pressure. To reduce the pressure to lower pressure, the system should be turned off.

Conclusion:

Hence, the work should be done before installing a gauge on the high-pressure side of a system is turn off the system.

Answer 14

Ch. 41 - Before installing a gauge on the high-pressure...Ch. 41 - Capacitors should be shorted with a(n)...Ch. 41 - The high- and low-side pressures on an operating...Ch. 41 - Why do most air-conditioning systems not need a...Ch. 41 - A typical standard-efficiency evaporator under...Ch. 41 - The typical temperature difference between the...Ch. 41 - When the ambient outside air temperature isand the...Ch. 41 - When the outside ambient air temperature is 90F,...Ch. 41 - If a condensing pressure is 260 psig for R-22,...Ch. 41 - How is high efficiency accomplished in an...

Before installing a gauge on the high-pressure side of a system, you should do which of the following? A. Turn on the system. B. Turn off the system. C. Adjust the system to a neutral position. D. Have a cylinder approved by the DOT nearby.

Videos

Answer to Problem 1RQ

Explanation of Solution

Want to see more full solutions like this?

Chapter 41 Solutions