
Concept explainers
What industry first started using programmable logic controllers?

The first industry to use programmable logic controllers.
Explanation of Solution
The programmable logic controllers were first used in the automotive industry. The automotive industry started using programmable logic controllers during the late 1960s.
The automotive industry had the necessity to change the control system operation for every newly designed automobile and it required to physically rewire the control system to perform the new operations that were expensive and time consuming.
Thus, the industry required a control system that could be changed without rewiring the system. The programmable logic controllers were then used to change the control system without excessive rewiring.
Want to see more full solutions like this?
Chapter 38 Solutions
Understanding Motor Controls
- Calculate the Shear Force at Point F on the beam below. Keep your answer in Newtons and make shear force positive to the right. A х 2m <2m E D 5m 1m Хт 325N1m 400N/m 8arrow_forwardThe normal force at C on the beam below is equal to: A ShN C X 15h N 8 ○ OkN 2.5kN 10kN ○ 12.5kN 1m Im 1m 1m;arrow_forwardCalculate the y coordinate of the of the centroid of the shape below. Take A= 18.5 8 6A 4A X 6Aarrow_forward
- In MATLAB write out a program to integrate the equations of motion of a rigid body. The inertia matrix is given by I = [125 0 0; 0 100 0; 0 0 75] which is a diagonal, where diag operator provides a matrix with given elements placed on its diagonal. Consider three cases where the body rotates 1 rad/sec about each principal axis. Integrate the resulting motion and study the angular rates and the resulting attitude (use any attitude coordinates). For each principal axis case, assume first that a pure spin about the principal axis is performed, and then repeat the simulation where a small 0.1 rad/sec motion is present about another principal axis. Discuss the stability of each motion. The code should produce a total of 6 simulations results when it is ran.arrow_forwardQ. A strain gauge rosette that is attached to the surface of a stressed component C). If the strain gauge rosette is of the D° gives 3 readings (a = A, b = B, &c = type (indicating the angle between each of the gauges), construct a Mohr's Strain Circle overleaf. You should assume that gauge A is aligned along the x-axis. Using the Mohr's Strain Circle calculate the: [10 marks] 100 918 ucy evods gringiz ya mwo quoy al etsede 39 926919 (i) principal strains (1, 2)? (au) oniona [5 marks] (ii) principal angles (1, 2)? You should measure these anticlockwise from the y-axis. 20 [5 marks] (iii) maximum shear strain in the plane (ymax)? Ex = Ea Ey = εc [5 marks] (epol) (apob) é Ea = A = -210 2 B=E₁ = -50 E₁ = C = 340 D = 45° bril elled ✓A bedivordan nemigas olloho shot on no eonsoup Imeneo alubom shine sail-no viss ieqse sidetiva bnat sabied 2arrow_forward1) Solve and show which is converage or diyverage a = 2+(0.1)" 3 16) a = n 1-2n 2) a = In n 1+2n 17) a = n 1-5n4 3) an = n* +8n³ 18) a =√4"n n² -2n+1 n! 20) a = 4) a₁ = 10 n-1 (Ina) 5) a=1+(-1)" 21) a= 6) a 7) an = * = (12+) (1-1) 2n (-1)+1 2n-1 3n+1 22) a= 3n-1 x" 23) a= .x>0 2n+1 2n 3"x6" 8) a = 24) a = n+1 π 9) a = sin 2 sin n 10) an = n + 2 x n! 25) a = tanh(n) n² 1 26) a = -sin- 2n-1 27) a = tan(n) n n 11) a = 2" 12) a = n 13) a = 8/ +=(1+2)" 14) a = 15) a = √10n In(n+1) 29) a = n 30) an-√n²-1 1 28) a = + √2" (In n)200 n 31) a=- = 1 dx nixarrow_forward
- HW12 A multiple-disc clutch has five plates having four pairs of active friction surfaces. If the intensity of pressure is not to exceed 0.127 N/mm², find the power transmitted at 500 r.p.m. The outer and inner radii of friction surfaces are 125 mm and 75 mm respectively. Assume uniform wear and take the coefficient of friction = 0.3.arrow_forwardThe sketch below gives some details of the human heart at rest. What is the total power requirement (work/time) for an artificial heart pump if we use a safety factor of 5 to allow for inefficiencies, the need to operate the heart under stress, etc.? Assume blood has the properties of water. p pressure above atmosphere blood going to the lungs for a fresh charge of oxygen p = 2.9 kPa 25v pulmonary artery d = 25mm fresh oxygenated blood from the lungs p = 1.0 kPa vena cava d=30mm right auricle pulmonary vein, d = 28mm aorta, d=20mm spent blood returning from left auricle the body p = 0.66 kPa right left ventricle ventricle blood to feed the body, p 13 kPa normal blood flow = 90 ml/sarrow_forward4- A horizontal Venturi meter is used to measure the flow rate of water through the piping system of 20 cm I.D, where the diameter of throat in the meter is d₂ = 10 cm. The pressure at inlet is 17.658 N/cm2 gauge and the vacuum pressure of 35 cm Hg at throat. Find the discharge of water. Take Cd = 0.98.arrow_forward
- Understanding Motor ControlsMechanical EngineeringISBN:9781337798686Author:Stephen L. HermanPublisher:Delmar Cengage LearningPrecision Machining Technology (MindTap Course Li...Mechanical EngineeringISBN:9781285444543Author:Peter J. Hoffman, Eric S. Hopewell, Brian JanesPublisher:Cengage LearningAutomotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning


