Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
6th Edition
ISBN: 9780135257272
Author: James D. Halderman
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Videos
Textbook Question
Chapter 2, Problem 3CQ
All of the following are usual duties of a lube technician except __________.
- a. oil change
- b. air filter replacement
- c. water pump replacement
- d. accessory drive belt inspection
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solution
Students have asked these similar questions
Technician A says the front wheel bearings on a typical FWD car are sealed and non-adjustable. Technician B says the front wheel bearings on a typical FWD car are greaseable and adjustable. Who is correct?
Which of the following is part of the sprung weight ofa vehicle?a. Steering linkageb. Tiresc. Engined. All of the above
Which of the following statements about unibodyconstruction is not true?a. A unibody is a stressed hull structure in whicheach of the body parts supplies structural supportand strength to the entire vehicle.b. Unibody vehicles tend to be tightly constructedbecause the major parts are all welded together.c. All unibodies are constructed from steel.d. Most front-wheel-drive unibody vehicles have acradle or partial frame.
Chapter 2 Solutions
Automotive Technology: Principles, Diagnosis, And Service (6th Edition) (halderman Automotive Series)
Ch. 2 - What should be included on a work order?Ch. 2 - Prob. 2RQCh. 2 - what tasks are usually performed by a general...Ch. 2 - Prob. 4RQCh. 2 - Prob. 5RQCh. 2 - A vehicle needs a repair while still under...Ch. 2 - A service advisor is called a ____________. a....Ch. 2 - All of the following are usual duties of a lube...Ch. 2 - New vehicle preparation is usually an entry-level...Ch. 2 - What is not a duty of a general service...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Technician A uses sandpaper to remove carbon deposits from turbocharger wastegate parts. Technician B scrapes off heavy deposits before attempting to clean the unit. Who is correct?arrow_forwardWhich of the following components is replaced as an assembly?a. The transfer caseb. the viscous clutchc. The interaxle differentiald. all wheel drive transaxlesarrow_forwardWhich of the following statements about drum brakeshoes is not true?a. Web thickness varies only with changes in shoesize.b. Many shoes have indented places along the edgeof the rim.c. The shoe rim is welded to the web.d. The primary/leading shoe is typically the one thatis positioned toward the front of the vehiclearrow_forward
- The stoplight switch is normally mounted on the instrument panel transmission brake pedal arm none of the abovearrow_forwardAll of the following should be done post-repair EXCEPT: Select one: a. go back through the vehicle and look for tools. b. ensure that no damage to the vehicle has been sustained during repair. c. look for worn tires and wiper blades. d. check that all fingerprints have been removed. Next pa page O Marrow_forwardWhat is the name for the gas-filled pressure chamberthat is part of the antilock braking system’s pump andmotor assembly?a. Control moduleb. Accumulatorc. Sensord. Reservoirarrow_forward
- A customer comes in with an indirect TPMS, complaining that despite all the tires running low on pressure, the TPMS light never came on. Technician A says it’s likely due to a faulty module. Technician B says it may just be normal operation of an indirect TPMS. Who is correct? Technician A Technician B Both Technician A and B Neither Technician A or Barrow_forwardTechnician A says power brakes are designed with vacuum-assisted units that use engine vacuum. Technician B says power brakes are designed with vacuum-assisted units that use vacuum developed by an external pump. Who is correct? a. A only b. B only c. both A and B d. neither A nor B Synthetic linings are made of _____ a. fiberglass b. aramid fiber c. both A and B d. neither A nor B All manufacturers recommend a specific sequence to follow when bleeding a vehicle’s brakes. a. True b. False Organic friction material _____ semimetallic materials. a. is quieter than b. is more fade resistant than c. requires higher pedal pressure than d. wears out faster thanarrow_forwardA technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling system pulled into a vacuum when cold. Technician A states that a leak in the surge tank could be the cause. Technician B states that the radiator cap is most likely defective. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor Barrow_forward
- Technician A uses a crane to remove an engine from its compartment- Technician B uses an engine cradle to remove an engine from its compartment Who is correct? Technician A Technician B Both A and B Neither A nor Barrow_forwardTechnician A says that seat belt webbing should be replaced if it is bowed. Technician B says that webbing does not need to be replaced if the color has merely faded due to exposure to the sun. Who is correct? Technician A only Technician B only Both A and B Neither A nor Barrow_forwardBefore delivering the vehicle to the customer, it is important to check the vehicle for cleanliness. Technician A says that all the trash from the repair process needs to be removed. Technician B says that we must ensure that all the windows are clean and free of hand prints. Who is correct? Select one: a. Technician A b. Technician B 1x c. Both A and B d. Neither A nor Barrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
Automotive Technology: A Systems Approach (MindTa...Mechanical EngineeringISBN:9781133612315Author:Jack Erjavec, Rob ThompsonPublisher:Cengage Learning
Automotive TechnologyMechanical EngineeringISBN:9781337794213Author:ERJAVEC, Jack.Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...Mechanical EngineeringISBN:9781305578296Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill JohnsonPublisher:Cengage Learning
Automotive Technology: A Systems Approach (MindTa...
Mechanical Engineering
ISBN:9781133612315
Author:Jack Erjavec, Rob Thompson
Publisher:Cengage Learning
Automotive Technology
Mechanical Engineering
ISBN:9781337794213
Author:ERJAVEC, Jack.
Publisher:Cengage,
Refrigeration and Air Conditioning Technology (Mi...
Mechanical Engineering
ISBN:9781305578296
Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson
Publisher:Cengage Learning
Mechanical Design (Machine Design) Clutches, Brakes and Flywheels Intro (S20 ME470 Class 15); Author: Professor Ted Diehl;https://www.youtube.com/watch?v=eMvbePrsT34;License: Standard Youtube License