When installing a motor control system, list four major factors to consider concerning the power system.

Question

Want to see more full solutions like this?

Answer 1

Textbook Question

Chapter 1, Problem 1RQ

When installing a motor control system, list four major factors to consider concerning the power system.

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Students have asked these similar questions

Find the resultant force vector from adding F1, F2 and F3, where … F1 = {-8i+10j-32k} N F2 is 40 N in magnitude with coordinate direction angles α, β, and γ, of 45, 120 and 60 degrees, respectively and F3 is 22 N in magnitude with transverse and azimuth angles of 65 and 40 degrees, respectively Express your final answer as a Cartesian vector as well as a magnitude with angles.

A 2-kW resistance heater wire with thermal conductivity of k=20 W/mK, a diameter of D=4mm, and a length of L=0.9m is used to boil water. If the outer surface temp of the resistance wire is Ts=110 degrees C, determine the temp at the center of the wire.

A flat-plate solar collector is used to heat water by having water flow through tubes attached at the back of the thin solar absorber plate. The absorber plate has emmisssivity and an absorptivity of 0.9. The top surface where x=0 temp of the absorber is T0=35 degrees C, and solar radiation is incident on the basorber at 500 W/m^2 with a surrounding temp of 0 degrees C. The convection heat transfer coefficient at the absorber surface is 5 W/m^2 K, while the ambient temp is 25 degrees C. Show that the variation of the temp in the basorber plate can be expressed as T(x)=-(q0/k)x+T0, and determine net heat flux, q, absorbed by solar collector.

Answer 2

Textbook Question

Chapter 1, Problem 1RQ

When installing a motor control system, list four major factors to consider concerning the power system.

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 3

Textbook Question

Chapter 1, Problem 1RQ

When installing a motor control system, list four major factors to consider concerning the power system.

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 4

Textbook Question

Chapter 1, Problem 1RQ

When installing a motor control system, list four major factors to consider concerning the power system.

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Want to see more full solutions like this?

Subscribe now to access step-by-step solutions to millions of textbook problems written by subject matter experts!

Answer 5

Textbook Question

Answer 6

Textbook Question

Answer 7

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Answer 8

Expert Solution & Answer

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Answer 9

Expert Solution & Answer

Answer 10

Expert Solution & Answer

Answer 11

To determine

The four major factors to be considered when installing a motor control in concern with the power system.

Answer 12

Explanation of Solution

The electrical connections that are associated with a motor, machine, and control unit are easy or complex. However, the below-listed factors should be considered while installing a motor and its control.

Power source –– Check whether the motor and control unit require a single-phase or three-phase power supply with rated voltage and current.
Motor connections –– A motor connection should be made based on the information found on the name plate of a motor. The name plate of a motor contains information such as horsepower, service factor, voltage, and full load current rating.
Controller type –– In general, a motor requires simple controller that starts and stops the motor. In addition, a motor may require controllers that vary the speed of the motor at specified time, inching, and jogging.
Environment –– The environment should not affect a control unit. The elevated temperature and moisture may affect a control unit.

Answer 13

Ch. 1 - When installing a motor control system, list four...Ch. 1 - Prob. 2RQ Ch. 1 - Is the National Electrical Code a law?Ch. 1 - Explain the difference between manual control,...Ch. 1 - Prob. 5RQ Ch. 1 - Explain the difference between jogging and...Ch. 1 - Prob. 7RQ Ch. 1 - What agency requires employers to provide a...Ch. 1 - What is meant by the term ramping? Ch. 1 - What is the most important function of any control...

When installing a motor control system, list four major factors to consider concerning the power system.

Concept explainers

Videos

Explanation of Solution

Want to see more full solutions like this?

Chapter 1 Solutions