Concept explainers
In a work situation where an electrician’s hands get wet while operating a 120-volt, corded drill, which of the following would be true? (Objective 1-1)
a. Body resistance increases, and any shock would be mild.
b. Body resistance remains the same, and there is no danger as Long as rubber boots are worn.
c. Body resistance is substantially decreased, and severe shock could occur.
d. There is no danger as Long as a three-prong plug is used.
The true statement for the situation where an electrician’s hands get wet while operating a
Answer to Problem 1RQ
Option (c) Body resistance is substantially decreased, and severe shock could occur.
Explanation of Solution
Introduction:
According to the Ohm’s law, the relation between the current, voltage, and resistance is given by,
Here, the current is in amperes, voltage is in volts, and resistance is measured in Ohm’s.
The flow of current through any material depends upon the resistance provided by the material. The higher is the circuit resistance, the lower the current flow that a voltage can push through the circuit and vice-versa.
Dry skin offers much more resistance in comparison to the wet body. This means that higher the resistance value, the more opposition to the current flow through the body.
The following table shows the value of resistance with respect to the different conditions:
Skin Condition | Resistance |
Dry skin | |
Sweaty hands | |
In water |
As shown in the above table, the value of resistance for wet hands is very less so if in a work situation where an electrician’s hands get wet while operating a
As shown in the above table, the value of resistance for wet hands is very less, so the shock will not be mild. Thus, option (a) is incorrect.
Therefore, the body resistance will not remain the same if the hand gets wet. Thus, option (b) is incorrect.
The electrician will always be in danger if his hands are wet. Thus, option (d) is incorrect.
Conclusion:
Therefore, the Option (c) Body resistance is substantially decreased, and severe shock could occur is best suitable answer for the given statement.
Want to see more full solutions like this?
Chapter 1 Solutions
Residential Construction Academy: House Wiring (MindTap Course List)
- Q5: Given the following system: น -3 y= [4 -2] +3u Generate a model with states that are the sum and difference of the original states.arrow_forward4. Draw a stress-strain curve (in tension and compression) for a reinforced concrete beam below. Label the important parts of the plot. Find the linear elastic approximation obtained using the transformed technique, and plot over the same strain ranges. 24" 4" 20" 16" f = 8,000 psi 8- #11 bars Grade 60 steel 4" (f, = 60 ksi and E₁ = 29000 ksi)arrow_forwardWhy is Historical Data important compared to other sourses of information when estimating construction projects?arrow_forward
- Need help, please show all work, steps, units and round to 3 significant figures. Thank you!!arrow_forwardNeed help. Find the answer to the boxes marked in red. Thanks!arrow_forwardFor the gravity dam shown in the figure, The following data are available: -Unit weight of concrete (Yconc) = 2.4 ton/m³ -Vertical upward earth quake factor (K,) = 0.1 -Neglect Wave pressure, silt pressure and ice force μ=0.65 a-Find heel and toe stresses (Pmin & Pmax) b-Is this structure safe against tension? c-Find the factor of safety against sliding and overturning (F.S, & F.Sover) 165 m 160 m t 10 m T I 4 m 50 100 marrow_forward
- For the gravity dam shown in the figure, The following data are available: -Unit weight of concrete (Yeone) 2.4 ton/m³ Vertical down ward earth quake factor (K,) = 0.1 Neglect Wave pressure, silt pressure and ice force The wind velocity (V)-45 Km/hr Straight length of water expanse (F) 75 Km =0.7 14-70m 3h T a- Find the factor of safety against sliding and overturning (F.Slid F.Sover) b- Find the toe and heel stresses (hma, and hmin.) c-Check tension. 8marrow_forwardQUESTION 2-(40 Points) In the case where other information is given in the figure, the wall is under the effect of a uniform lateral wind load of 0.7 kN/m2. Since the foundation is sized according to the safe bearing capacity of the soil and the safe bearing capacity remains the same, find the width of this foundation asymmetrically (with uniform base pressure). Draw the vertical section of the wall of the asymmetric foundation and write its dimensions and values on it. Draw the T and M diagrams along the width. The foundation thickness is the same in both cases. q=0.7 kN/m2 5 m R Duvar Nd=Wd 0.7 m T K 0 0.6 0.5 1.7 m Yb-24 kN/m3 0.6 m T + foundationarrow_forwardCan you pls. Explain on how to get "BETA T" and "BETA C" on this study about VALUE OF TRAVEL TIME.arrow_forward
- 440 CHAPTER 9 ANALYSIS OF STATICALLY INDETERMIN 9-23. Determine the reactions at the supports, then draw the moment diagrams for each member. Assume A and B are pins and the joint at C is fixed connected. EI is constant. Se 9-2 12 kN 2 m 2 m 6 kN/m A 6 m Prob. 9-23 Barrow_forwardI need a solution to this problemarrow_forwardThree forces act on the ring. If the resultant force FR has a magnitude and direction as shown, determine the magnitude and the coordinate direction angles of force F3. == F2 = 110 N F3 F₁ = 80 N 3 X 45° FR = 120 N 30° yarrow_forward
- Residential Construction Academy: House Wiring (M...Civil EngineeringISBN:9781337402415Author:Gregory W FletcherPublisher:Cengage LearningSolid Waste EngineeringCivil EngineeringISBN:9781305635203Author:Worrell, William A.Publisher:Cengage Learning,