ll MIN11:46 AM24% OWater of density 1000 kg/ m³ and kinematic viscosity 1.022 X 106 m²/s, is pumpedbetween two reservoirs at 5.66 X 103 m³/s through 122 m of 50.8-mm-diameterpipe and several minor losses, as shown in Figure below. The roughness ratio is e/D= 0.001. Compute the pump horsepower required. K-values for bends and fittingsare given in the table below.LosK-ValueSharp entranceOpen globe valve12-in bend0.56.90.25Regular 90° elbowHalf-closed gate valveSharp exit0.952.71.0

Answered: Image /qna-images/answer/439c6563-9a64-4f27-8482-aeeda32bf2ea.jpg

Water of density 1000 kg/ m³ and kinematic viscosity 1.022 X 106 m²/s, is pumped between two reservoirs at 5.66 X 103 m³/s through 122 m of 50.8-mm-diameter pipe and several minor losses, as shown in Figure below. The roughness ratio is €/D = 0.001. Compute the pump horsepower required. K-values for bends and fittings are given in the table below. Loss K-Value Sharp entrance Open globe valve 12-in bend 0.5 6.9 0.25 Regular 90° elbow Half-closed gate valve Sharp exit 0.95 2.7 1.0

Water of density 1000 kg/ m³ and kinematic viscosity 1.022 X 106 m²/s, is pumped between two reservoirs at 5.66 X 103 m³/s through 122 m of 50.8-mm-diameter pipe and several minor losses, as shown in Figure below. The roughness ratio is €/D = 0.001. Compute the pump horsepower required. K-values for bends and fittings are given in the table below. Loss K-Value Sharp entrance Open globe valve 12-in bend 0.5 6.9 0.25 Regular 90° elbow Half-closed gate valve Sharp exit 0.95 2.7 1.0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1
Explain the major and minor losses? Then solve for the parallel pipes system shown below, a pump is placed in line 2 so that 0.142 m³/s will flow through each pipe. Pipe material is cast iron and for each elbow. Find the relation between the head loses hL1 and h12 and estimate the necessary pump head. Water viscosity is μ=1x10-³ Pa.s. Line 1, L-30 m, D= 6 inches Q₁-0.142 m³/s Pump Line 2, L, 30 m, D-3 inches Q-0.142 m/s R
Two 32-in pumps from Fig. are to be used in seriesat 1170 r/min to lift water through 500 ft of vertical castiron pipe. What should the pipe diameter be for most effi -cient operation? Neglect minor losses.
State clearly your assumptions in your solution sheet
The water is delivered with piping system given in the figure below. The levation difference between entering section and tank is 143,55 m. Estimate the gage pressure [MPa] at point 1. (Note: For water at 20°C, take p=998 kg/m and u=0.001 kg/ms. ) 5 cm diameter cast-iron pipe Length of the system is 1.2 km All fittings are flanged. The vohume flow rate is 300 L min 45 treaded elbow Yanit
None
I need the answer at 20 minute
If the water surface elevation in reservoir B is 110 m, what must be the water surface elevation in reservoir A if a flow of 0.03 m^3/s is to occur in the cast iron pipe. Use f= 0.0021 for all pipes. (DO NOT ROUND OFF)
Which of the following equations below describes the system head of the piping shown below. The total length of the pipe is 154 ft. Take the friction factor to be 0.026. The pipe used has a nominal diameter of 4 inches and Schedule No. 40. The system head H is in ft and the flow rate Q is in ft3/s. a. H = 51 + 25.98(Q^2) b. H = 54 + 24.98(Q^2) c. H = 54 + 25.98(Q^2)
Solve it correctly please. I will rate accordingly with 4votes.
QUESTION 6 Pump BC in figure delivers 8 cfs through the pipe system shown. The elevation at reservoir D has to be maintained at 77 ft. There is a valve in the discharge pipe with a loss coefficient of 5. Neglect other minor losses. EL 20.0 37 20 78 20-18 f-0.030 400-12" EL. 10.0-0.020 The head (ft) developed by the pump is: 57 K=5.0
PROBLEM 3 Water, p = 1000 kg/m³ and μ = 0.001 kg/m.s, is pumped between two reservoirs at 5 liter/s through 125 m of 5 cm-diameter pipe and several minor losses, as shown in Fig. The roughness ratio is e/d= 0.001. Compute the pump horsepower required. 2₂= 40m Screwed regular 90° elbow Sharp exit Ģ2 1 2₁ = 7m GI Sharp entrance Half-open gate valve Open globe valve 30 cm bend radius 125m of pipe, d= 5 cm Pump