Water is flowing in a tube "D=3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. If the Power rating is 11kW and the convective heat transfer coefficient is 864 W/m.K, what is the surface temperature at the exit

Water is flowing in a tube "D=3 cm, L= 5 m" and is to be heated from 15°C to 47°C by applying a uniform heat flux on the outer surface of the tube by electric resistance heater. If the Power rating is 11kW and the convective heat transfer coefficient is 864 W/m.K, what is the surface temperature at the exit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3 a) A rectangular duct with width of 0.3 m and height of 0.2 m is used to deliver cold fresh air to a medium size master bedroom. Heat from roof causes the internal surface temperature of the duct to be 40°C. The fresh cold air enters the duct at 17°C and exits at 23°C. Given the volumetric flow rate of the fresh cold air which enters the duct is 0.15 m/s, assuming the flow inside the duct is fully developed: i) State two assumptions for analyzing this problem ii) Calculate the Reynolds number for the flow inside the duct iii) Calculate the heat transfer rate to the fresh cold air inside the duct, kW iv) What is the minimum length of the duct to keep the exit temperature at 23°C, m b) Will the exit temperature remain the same which is at 23°C, if the length of the duct is increased 5 times of the length calculated in iv)? Explain and sketch a temperature variation along the length of the duct to justify your answer.
In a chemical plant, a certain chemical is heatedby hot water supplied by a natural gas furnace. The hot water(cp= 4180 J/kg·K) is then discharged at 60°C at a rate of 8 kg/min. The plant operates 8 h a day, 5 days a week, 52 weeks ayear. The furnace has an efficiency of 78 percent, and the costof the natural gas is $1.00 per therm (1 therm = 105,500 kJ).The average temperature of the cold water entering the furnacethroughout the year is 14°C. In order to save energy, it isproposed to install a water-to-water heat exchanger to preheatthe incoming cold water by the drained hot water. Assumingthat the heat exchanger will recover 72 percent of the availableheat in the hot water, determine the heat transfer rating of theheat exchanger that needs to be purchased and suggest a suitabletype. Also, determine the amount of money this heat exchangerwill save the company per year from natural gas savings.
A condenser consists of several tubes. The outer diameter of each tube is 2 cm, and the thickness is 2 mm. It is designed to condense saturated steam that enters the condenser at the mass flow rate of 100 kg/s. The steam pressure is 10 kPa. There is 10% moisture in saturated steam. The inlet temperature of cooling water is 20°C, and the outlet temperature is 40°C. Water velocity 2 m/s. The overall heat transfer coefficient based on outer surface area is 3.5 3. kW/m2.K. The heat capacity of water is 4.2 kJ/kg.K. Water density is 1000 kg/m'. Find the number of tubes and the length of each tube.
In a once-through boiler, feed water enters through the bottom of tubes, receives heat from combustion of coal, and escapes from the top of the tubes as superheated steam, calculate the heat transfer coefficients of water and superheated steam using the following data: Pressure of feed water at tube inlet = 22.0 MPa Absolute temperature of feed water, Tf =523 K Pressure of superheated steam at tube outlet = 22.5 MPa %3D Absolute Temperature of superheated steam, Tg = 868 K Velocity of Feed water through each tube. Vf = 8 m/s Internal diameter of each tube = 53.5 mm %3D Length of pipe = 120m Use, Density of water = 818.25 kg/m3 Density of steam = 63.34 kg/m3 %3D
Water at 90C is being pumped from a large storage tank at 1 atm abs at a rate of 0.189 m3/min by a pump. The motor that drives the pump supplies energy to the pump at a rate of 2 hp. The water pumped through a heat exchanger, where it gives up 700 kW of heat and is then delivered to a large open storage tank at an elevation of 20 m above the first tank. What is the final temperature of the water to the second tank? Neglect kinetic energy.
Water (cp=4.182 kJ/kg.K, k=0.6405 W/m.K, Pr=3.57, ν=0.5537x10-6 m2/s, ρ=998 kg/m3) flows through a tube (D=0.5 cm) with an average velocity of 0.2 m/s. The average temperatures of the water at the inlet and outlet cross-sections are 26,03 oC and 86,92 oC, respectively. The uniform heat flux of 0,82 W/cm2 is subjected to the surface of the tube for heating process. Determine the tube length [m].
The air duct of the heating system of a hall, an electric heater placed inside andIt consists of a 300 W fan. While the air is continuously flowing in the duct with a flow rate of 0.6 kg/stemperature rises by 5°C. Since there is a loss of 400 W 151 from the channel surfaces to the environmentCalculate the power of the electric heater. (The specific heating value of air is - 1.005 kJ/kgK.)
The water (C, = 4180 J/kg - °C) enters the 2.5-cm internal-diameter tube of a double-pipe counter-flow heat exchanger at 17°C at a rate of 3 kg/s. It is heated by steam condensing at 120°C (he = 2203 kJ/kg) in the shell. If the overall heat transfer coefficient of the heat exchanger is 1500 W/m? - °C, determine the length of the tube required in order to heat the water to 80°C. Steam 120°C Water 80°C 17°C 3 kg/s
Q3. White potatoes (k = 0.50 W/m. °C and a = 0.13 x 106 m²/s) that are initially at a uniform temperature of 25°C and have an average diameter of 6 cm are to be cooled by refrigerated air at 2°C flowing at a velocity of 4 m/s. The average heat transfer coefficient between the potatoes and the air is experimentally determined to be 19 W/m². °C. Determine how long it will take for the center temperature of the potatoes to drop to 6°C.
Calculate the rate of infiltration heat loss of a room with a 150m^2 floor area and 3.6m high ceilings. Use an inside temperature of 20°C, an outside ambient temperature of 37.4°C, and an hourly ACH of 0.2 m^3. Assume the heat capacity of air is 0.717W/°C•m^2.
Air at p = 1 atm enters a thin-walled (D = 5-mm diameter) long tube (L = 2 m) at an inlet temperature of Tm,i = 100°C. A constant heat flux is applied to the air from the tube surface. The air mass flow rate is m = 125 × 10-6 kg/s. If the tube surface temperature at the exit is T, = 160°C, determine the heat rate entering the tube, in W. Evaluate properties at T = 400 K. q= Mi W
Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.