w PROCEDURE : 1. Compute the moment and Shear' at the support Coptianal) 2. Draw the elastic curve of the beam. 3. Draw a tangent line on the elastic curve taken at the fixed-ended support. 4.' Construct the 'moment diagram by parts. 5. Compute te/A, Note': it will be noticed thed the magnitude of to/A will poind B. eoval He defleeion under teyA - I tejA. I (Area DAG:XB El

w PROCEDURE : 1. Compute the moment and Shear' at the support Coptianal) 2. Draw the elastic curve of the beam. 3. Draw a tangent line on the elastic curve taken at the fixed-ended support. 4.' Construct the 'moment diagram by parts. 5. Compute te/A, Note': it will be noticed thed the magnitude of to/A will poind B. eoval He defleeion under teyA - I tejA. I (Area DAG:XB El

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(+) The hollow shaft used in the system has the following conditions: В E Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the F 35 kN-m nearest whole number for the thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN-m
Problem I A 2.25-kg slender rod AB and a 1.85-kg slender rod BC are connected by a pin at B and by the cord AC. The assembly designed by engineers can rotate in a vertical plane under the combined effect of gravity and a couple M applied to rod BC. Knowing that in the position shown, the 300 mm angular velocity of the assembly is zero and the tension in cord AC is equal to 25.0 N, determine; A (a) the angular acceleration of the assembly (b) the magnitude of the couple, M 400 mm C 400 mm AM B
It is propped cantilever case . ( Hint: So to obtain reaction at roller support balance the deflection due to roller reaction and due to 20kN load) Solve all three parts...
Calculate the maximum intensity w of the uniform distributed load that can be applied on the beam without causing the compressive members of the supporting truss to buckle. The members of the truss are made from A-36-steel rods having a 60-mm diameter. Use FS. = 2 against buckling. Need accurate answer only
Problem 8 A force system is shown consists of Couple C and four forces. If the resultant of this system is a 80000-N.mm counterclockwise couple. y 100 N 12 35 mm P 500 N -- B -35 mm a. Determine the magnitude P? b. Determine the magnitude Q? c. Determine the magnitude C? :: ::: ******
Vertical load is applied to point B of a 10 mm radius cylindrical bar as shown in the figure. Calculate the shear stress occurring at point D.
CE - PC 311 - STRUCTURAL THEORY Quiz No. 2F - Analysis of S tatically In determ in ate Beam s 1. By the moment-area method find the slope and de flection at the fre e end A of the cantile ver beam AB. E = 30,000k/in and I = 200 in ". Re fer to the fig ure belo w. A ll decim a ls must be in c lu ded, do not round off answers. All fig ures must be included and drawn straight. Curves may be done freehand. Sum marize your answers as shown b e lo w. w kit ft ft 1.110 7 8 Required Va lu es Answer O A A L1 L2 B.
4. Determine the x, y, z components of reaction at the ball-and-socket joint A and the tension in each of the wires, if the load weighs 100kg. 1m 2m 1m D F A 1.5m B G 1m, 1m 1m.
Determine the internal normal force and shear force, and the bending moment in the beam at points Cand D. Assume the support at B is a roller. Point Cis located just to the right of the load P which is equal to 78.1N. Report the Bending moment in the beam at point D (Mp) here in Moodle. NB: • FBDS are required • Your answer should contain ALL the necessary steps
A hollow aluminium shaft of 80 mm outer diameter & 60 mm inner diameter is rotating @5 Hz when constant 120 KW is applied. Use the following: G(alum)-28 GPa, a=1.80 m, b=0.80m & L-2.60 m. Assumed that the angle of twist is constant.The torque "T2" developed at right fixed support at B is_KN-m B E 1.18 0.48 2.64 3.82 5.03
Two cylindrical bars, AB and BC are connected at point B as shown. Knowing that d1 = 50mm and d2 = 30mm, find the voltages normal in the AB and BC stretches. Admitting that the material of stretch AB is aluminum (E = 70 GPa), and of the BC section being steel (E=200 GPa), determine the displacements of points B and C.
Please answer po. With complete soultion. Thankyouu po