Paz: (A) On testing the water Contet forasoil Sample, we have got the followsng dato, wz = lo 8.7 gmpa.ouノW2WI : 58.7 9ml05.1er.r.w3= gmen

given values are w1=58.7gm w2=108.7gm w3=105.1gm

Answered: Va 2:(A) On testing the water content…

Va 2:(A) On testing the water content for asoil Sample, we have got the followpng date wI = 58.7 gm wie lo5.| gm , wz = lo 8.7gm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following waste water test result were obfecined fox test of teken-The Simple concen foation solids, Suspended susporded a Simple were pecfooned. eusing the 50 mL Calculate oftotel and volctile Solid solids votit volatile Mass of empty dish =62.0039sam mass of 4 Mass %3D dish t doy Solids = 62.0394 %3D dish + igmited solids = 62: 0367 of u Mass of filter=1540 gram of filter tday solids = 1-S5agsom %3D L) MUss y muss of filtest iynited Solids 1:5494 こ

Please fine the overall density for me ple
Q2. A ring infiltrometer (inside area is 962 cm²) test was made on a soil with the results shown in the table below. Elapsed 10 20 30 60 90 150 time (Min) Wat.Vol 300 650 1190 1950 2500 3350 3900 4600 added since start c cubk cenembcr Determine the Horton's Infiltration equation.
An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 21 ft. The pipe is subjected to a wind loading that increases from WA = 12 lb/ft at its base to we = 18 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe? WB WA B L
* .A list of sources duration comprehensive successive moisture The teacher asks his students, after their lousy marks in the test: what * ?- all the semester are you doing O have you done had you done have you been doing
answer the four bits given in image. please solive them.
Q2: A column analysis for an activated sludge suspension yielded the following: MLSS Conc (mg/l) Settling velocity m/h 1000 2.8 2000 3000 1.2 0.4 4000 0.2 5000 Question 0.1 6000 0.06 The influent MLSS concentration is 2000 mg/l and the flow rate is 4200 m³/d. Determine the size of the clarifier that will thicken the solids to 8000 mg/l.
AVA araupp g A p u s A pup upp n. 1. Answer the following questions about porosity and permeability: a) Name three (3) parameters which are involved in calculation of porosity. b) Name four geological mechanisms affecting porosity values. c) Describe effect of sorting on porosity. d) Describe how porosity and permeability are associated with one another. e) Permeability is seldom uniform throughout a reservoir. Thus, it is necessary to ascertain an average value of permeability, kavg. Elaborate with suitable diagrams two (2) examples of permeability averaging techniques. f) Two sandstone reservoir formations designated A and B are located 1 km apart. Their properties are given in Table Q1(f). Outline FOUR (4) reasons for which reservoir B is commercially more viable than reservoir A.
The test Carried aut en an follow. detaits sludge Somple are Weight of Dish =9.52gm Baw Sludge Sempla and duch =23 27ga Aşter Drying Clnstent) After Burning Clnstant) = 6.38gm 9.46gm %3D %3D Calculkt th percentage of total Salidl ad lloldi Solid in t cboue of cowego.
A liquid limit test was performed on a soil sample It was found out that the moisture content at 14 blows was 72%, and that at 39 blows was 31%. What will be the resulting liquid limit of the soil? Round off to two decimal places. A Moving to another question will save this response. Activats Ruestion 5 of 20 Go to Settings to activate Winde ASUS CO CIB Ro D G 34
A primary clarifier is to be designed to treat a municipal wastewater. The influent to the clarifier has a flow rate of 7570 m³/d and a total suspended solids concentration of 320 mg/L. A laboratory settling test was performed with the following results: Suspended Solids Concentration (mg/L) at Given Depths Sampling Depth (m) Time (min) 0.61 1.22 246 2.44 272 243 1.83 3.05 10 230 262 282 20 157 195 230 253 30 115 160 211 221 230 45 90 134 163 179 195 60 48 102 131 154 170 90 29 58 86 115 141 (a) Determine the design overflow rate and detention time assuming 65% of the suspended solids are to be removed. Use typical scaling/safety factors as appropriate. (b) Determine the required diameter (to the nearest 0.1 m) and the required depth (to the nearest 0.01 m) for the clarifier.
The results of a water analysis for Sungai Buaya is shown below: = 2.5 meq/L Mg²* = 0.6 meq/L Na* 1.7 meq/L SO? = 2.0 meq/L 0.2 meq/L Ca²+ HCO; %3D 2+7 = 0.4 meq/L = 0.4 meq/L Cl K+ (i) Calculate the concentration for each cation and anion component in mg/L (ii) Draw a miliequivalent per litre bar graph (iii) List the hypothetical combinations with values (iv) Calculate the non-carbonate hardness in mg/L as CaCO3