Two steel springs arranged in series support a load, F. The upper spring has 12 turns of 25 mm diameter wire on a mean diameter of 200 mm. The lower spring consists of 10 active coils of 20 mm diameter wire with a mean diameter of 150 mm. If the maximum shearing stress in either spring must not exceed 220 MPa, determine the maximum value of F. Use G=83GPA. Select one: O a. 3849.35 N O b. 8723.75 N O c. 5700.60 N O d. 4444.35 N

Two steel springs arranged in series support a load, F. The upper spring has 12 turns of 25 mm diameter wire on a mean diameter of 200 mm. The lower spring consists of 10 active coils of 20 mm diameter wire with a mean diameter of 150 mm. If the maximum shearing stress in either spring must not exceed 220 MPa, determine the maximum value of F. Use G=83GPA. Select one: O a. 3849.35 N O b. 8723.75 N O c. 5700.60 N O d. 4444.35 N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A flange bolt coupling consist of 8-12.7mmꬾ steel bolts on a circle diameter of 304.80mm & 6-12.7mmꬾ steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ___ MPa. 6.80 1.50 3.20 4.30 8.10
The following rod has a diameter of 15 mm, and a length of 1000 mm, and was fixed at its one end to the wall. A force pair of 200 N is applied by a 500 mm length arm to the point A. Which material given below should be chosen for this rod material to keep the twist angle on the A plane less than 20°. Material Aluminium alloy Magnesium alloy Titanium alloy E, GPa 70 45 105 V 0,3 0,3 0,3 200 N 250 mm 250 mm 200 N
The composite shaft shown consists of two steel pipes that are connected at flange B and securely attached to rigid walls at A and C. Steel pipe (1) has an outside diameter of 164 mm and a wall thickness of 7 mm. Steel pipe (2) has an outside diameter of 114 mm and a wall thickness of 6 mm. Both pipes are 3-m long and have a shear modulus of 80 GPa. If a concentrated torque of 20 kN-m is applied to flange 8, determine the torque in pipe (1). ... 3 m 3 m 20 kN-m (1) (2) B A 10.98 kN-m в) 15.63 kN-m 9.40 kN-m 14.85 kN-m
Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20-mm diameter wire on a mean radius of 80 mm when the spring is supporting a load of 2 KN.
Two steel springs arranged in series supports a load P. The upper spring has 12 turns of 20-mm-diameterwire on a mean radius of 100 mm. The lower spring consists of 10 turns of 25-mm diameter wire on amean radius of 75 mm. If the maximum shearing stress in either spring must not exceed 300 MPa,compute the maximum value of P and the total elongation of the assembly. Use approximation formulaand G = 83 GPa. Compute the equivalent spring constant by dividing the load by the total elongation.
A load P is supported by two (2) concentric steel springs. The inner spring consists of 40 turns of 20 mm diameter wire on a mean diameter of 150 mm, the outer spring has 30 turns of 30 mm diameter wire on a mean diameter of 200 mm. Use G= 83000 MPa. a) Determine the maximum load that the inner spring could carry so as not to exceed a shearing stress of 140 MPa. b) Determine the maximum load that the outer spring could carry so as not to exceed a shearing stress of 140 MPa. c) Determine the maximum load that the spring could carry.
6. A rigid plate of negligible mass rests on the middle spring which is higher than the two outer springs by 20 mm. The middle spring consists of 24 turns of 25-mm diameter wire on a mean diameter of 150 mm. The two outer springs have 16 turns of 12-mm diameter wire on a mean diameter of 100 mm. Determine the shearing stress developed in each spring if P = 5 kN is applied. Use the Approximate formula. Use = 83 GPa. P=5 KN 20mm
20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? a. 8mm b. 3/8 inch 25 kN 12 mm C. 10 mm d. 1/2 inch 7.5 mm 12 mm 7.5 mm 25 kN 18. The motion of the follower of a cam-follower system is governed by x = R(1+1/2 coscot). If R = 70 mm and (= 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 c. 22 d. 24 b. 20
Only Handwritten solutions are allowed. No Chatgpt, you must have to draw the free body diagram.
A load P is supported by two steel springs arranged in series. The upper spring has 20 turns of ¾ in diameter wire on a mean diameter of 6 in. The lower spring consists of 15 turns of ½ in diameter wire on a mean diameter of 5 in. Determine the maximum shearing stress in each spring if the total deflection is 3 in. and G=12x106 psi. Clean and detailed solution. Thank you.
O A hollow circular shaft of inner radius 10 mm outer radius 20 mm and length 1 m is to be used as a torsional spring. If the shear modulus of the material of the shaft is 150 GPa, the torsional stiffness of the shaft (in kN-m/rad) is (correct to two decimal places).
Question 2 A composite shaft is comprised of a solid inner rod (shaft 1) made of a steel with an elastic modulus of 210 GPa, diameter of 70 mm, and length of 100 mm, and a hollow outer shaft (shaft 2) made of the aluminium with an elastic modulus 80 GPa, outer diameter of 100 mm, inner diameter of 80 mm, and a length of 100 mm that are rigidly attached to one another on both ends. The composite shaft is designed to absorb 150 joules of energy for deformation within its linear elastic limit upon application of an axial load onto a collar attached to its lower end. Determine the stresses induced in shafts 1 and 2, magnitude of the forces acting on shafts 1 and 2, and the total force acting on the composite shaft for the cases of: (i) A gradually applied load. (ii) A suddenly applied load. (iii) A mass that is dropped onto the collar from a height of 250 mm.