Two concentrated loads of 100 kN and 200 kN advance along a girder with a 20-metre  span, the distance between the loads being 8 metres. Find the position of the section that has to  support the greatest bending moment, and calculate the value of the bending moment. Please show a solution of the answer 1128 kNm at 10.3 m from one end.

Q: A beam is used to support a concentrated load of 12 kN and a distributed load (w). The beam has the…

A: ∑MB=0 -12 x 3 - RC x 9 = 0 RC = -4 kN ↓ ∑V=0 RA + RC = 6 x 9 - 12 RA = 46 kN ↑ ∑MA=0 -MA + 6 x 9 x…

Q: A simply supported beam 6m long is composed of two C 200x28 channels (use uniform weight of the beam…

A: Given:- Length of simply supported beam, L = 6 m = 6000 mm Section of the beam is made of two C 200…

Q: buoyant force acts in the direction opposite the force of

A: Buoyant force is the upward force exerted by fluid on object when it is submerged fully or partially…

Q: A rectangular section of size 100mm x 200 mm is used as a simply supported beam of 5m length. It is…

A: Given data : Width (B)=100 mmDepth (D)=200 mmLength of beam (L)=5 mCentral point load (W)=250 KNTo…

Q: 16 kN /m 13m

A:

Q: A flat slab is supPorted on600 mm dia <ircular <olumns spaced 8 m x 6 m apart in both directions.…

A:

Q: A rectangular beam has a width of 300mm and an effective depth of 550mm spand 4.0 meters on fixed…

A:

Q: The inverted T section of 6 m overhang bearn has the properties shown. The beam carries a uniformly…

A:

Q: Four wheel loads rolls as a unit across a 17-m span. The loads are 50 kN, 30 kN, 20 kN, and 20 kN…

A:

Q: Determine the forces in members CF, CG, and CD of the truss shown by method of section. Use P,=8 kN,…

A:

Q: 1.Three wheel loads roll as a unit across a 12m span. The leads are A-10 kN B-20 kN to the right of…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: etermine the forces in DF, EF, and EG in the truss shown diagrammatically in the figure.

A:

Q: 3. A 100 mm x 200 mm beam 6 m long is supported by a roller at its ends and at midspan. It carries a…

A:

Q: A reinforced concrete rectangular beam has a width of 315mm and an effective depth of 525mm. The…

A:

Q: 24 kN 5 kN 16 KN 16 kN 26 50 kN-m 100° В 35° A 1.6 m 2.2 m 2.4 m |1.2 ml 2.6 m A terrible driver has…

A:

Q: following multi-span beams. |20 kN B 10 kN 2 kN/m 3 m 3 m mi 4 m 题3.25 图

A:

Q: A reinforced concrete T-beam spaced at 3.0 m on centers has a span of 4.0 m with a slab thickness of…

A:

Q: A cantilever beam 6−ft6−ft long is made of steel, with a T-shaped cross section as shown below. If…

A:

Q: A uniform load of 2000 N/m, 5 m Long crosses a girder of 20 m span from left to right. Calculate the…

A: Given data:

Q: effective depth of 550mm and the width of the web section is 300mm. It is reinforced at the bottom…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 %3D kN, 2 m to…

A:

Q: Determine the Reactions of each beam. Show the Distributed Load Resultant magnitude and location on…

A:

Q: 2) 10 kN 10 kN 5 kN/m В D G |lm 3 m H 3 m 4 m

A: Answer:-                 In this question we will use the concept of hinge and equation of…

Q: For the continuous beam shown, determine the plastic moment capacity. L, = 6 m, L2 = 8 m, L3 = 5 m,…

A:

Q: An 87 meters long slope protection works with 75mm diameter x 1.0 meter PVC  Pipe for weep hole…

A:

Q: Problem 4.- Determine the force in member BE of the loaded truss and whether the member is in…

A: Given:- Forces:- 6kN.5kN,4kNTo find:-Force in member BE

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A 15 kN; B = 25 kN, 2 m to the…

A:

Q: 2- Determine the resultant force and specify where it acts on the beam measured from A. 15 kN/m B 4…

A:

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: A wooden rectangular beam 200 mm x 350 mm has a simple span of 6 m. It is subjected to a…

A:

Q: Four wheel loads rolls as a unit across a 16-m span. The loads are 40 kN, 40 kN, 20 kN, and 20 kN…

A:

Q: The girder of a simple log bridge supports a wheel load W acting at any position along the span. In…

A: Determine the maximum permissible wheel load W (in kN) based on an allowable shear stress,W?

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 kN, 2 m to the…

A:

Q: A simply-supported beam carries a uniform load, w = 123 kN/m at its middle third. If L = 14 m,…

A: Determine the absolute value of the maximum bending moment???

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.