triangular plate of height h=1.20 m and a base b=2.0 m is submerged vertically in water with its base at the liquid surface and parallel to it. a. Evaluate the total force acting on one side of the plate, in kN.      b. Obtain the location of the force from the center of gravity of the plate, in mm. c. Obtain the location of the force from the liquid surface, in mm.

Q: .) The two tugboats apply the forces P and Q Where P = 74 kN and Q = 50KN. Determine 32m 16m To 20m…

A:

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: To determine the force in the members BC, BE and BF of the given truss.   As we are to find the…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: 2. The block of weight W2 is being held in its position by two cylindrical rollers resting on…

A: Given Coefficient of static friction for all contact surfaces is 0.36 W1 = 516 kN

Q: The bar below is subjected to uniaxial tension. Assuming that the bar material behaves elastically,…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Given truss with point load of magnitude 14 kn is acting at joint D and it is asked to determine the…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Solution given in next step

Q: The rigid bars AC and BCD are supported by pins at A and B and by a steel rod at D. There is a…

A:

Q: Determine the forces in each members of 40 EN 3 m the truss loaded as shown. Tabulate the results…

A:

Q: 4

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Given Truss is asked to analyse to find forces in the members of BC, BE, EF By  using method of…

Q: Determine the reaction at the supports for the beam shown. The roller support B of the beam settles…

A:

Q: 2400 N 235° 25 960 N 960 N •6 @ 10.50 m 63 m a. Find the force in member AH. b. Find the force in…

A:

Q: A. Determine the x and y components of reaction at A. B. Determine the y component of reaction at B.

A: Given: F = 21 kN Free body diagram:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: The cylinder is subjected to a load that has a weight W. If the coefficients of rolling resistance…

A: The free body diagram of top surface is shown below.

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Given : To Find : Forces in member BC, BE and EF ?

Q: A 335-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: A pulling mechanism is given and it has been asked to determine load P required. Please refer step 2…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: 5. For a fluid at rest, the shear stress is zero. 6. Newton's law of viscosity for a fluid states…

A: As per guidelines we need to answer only 1st question so repost rest question separately

Q: Determine the horizontal displacement of joint C.  The length, L, of trusses AC, BC is 1,300 mm.…

A: EAC = 135 GPa = 135 × 103 N/mm2 EBC = 150 GPa = 150 × 103 N/mm2 AAC = ABC = 360 mm2 Determine the…

Q: Calculate (a) the elongation of the copper wire when the 50 KN vertical force is applied at and (b)…

A: Given data A copper with A= 500 mm2 L=1.30m E=120GPA P= 50 KN

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: 3. A bar AB is supported by fixed supports at its ends as shown in the figure. An axial load of 12…

A: Please find attached images for solution.

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

A:

Q: ant of the force system in next fig. Then locate 1000 N.m 80 N 10m 150 N 100 N 10m A

A: Determine the resultant of the force system in next fig. Then locate it with respect to point (A).

Q: A 466-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A:

Q: The cross-sectional area of each clamp forming a fixed-supported cage system from points C and D…

A:

Q: Q1/ Determine the resulting displacement of pin B. Assume: A1=A2= 900 mm? , E1=E2= 100 GPa, a1=a2=…

A:

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A:

Q: 114-lb block is resting on a r orizontal surface for which th ction is 0.5. Determine the f quired…

A: Given that Weight of block W = 114 lb Coefficient of friction f = 0.50 Let normal force acting…

Q: 1.0 m 3 m L- 2 m 3 m B

A:

Q: D (5000 mm2) (4000 mm) E (5000 mm) 3 m 4000 mm) (S000 mm?) B (5000 mm?) A 100 kN 2 panels at 4 m 8 m…

A:

Q: A 105-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: The answer is found to be P=42 lb For explanation please refer the attached solution, thanks

Q: A 247-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.