Three pipes steadily deliver water to a large exit pipe in the figure. The velocity v2 = 5 m/s, and the exit flow rate 04 = 174 m3/h. It is known that increasing 03 by 23 % would increase Q4 by 11 %. D₂=5 cm D₁ = 6 cm Ho¬ Find v₁ in m/s D₁ = 4 cm D₁ = 9 cm Express your answer in 2 decimal places.

Three pipes steadily deliver water to a large exit pipe in the figure. The velocity v2 = 5 m/s, and the exit flow rate 04 = 174 m3/h. It is known that increasing 03 by 23 % would increase Q4 by 11 %. D₂=5 cm D₁ = 6 cm Ho¬ Find v₁ in m/s D₁ = 4 cm D₁ = 9 cm Express your answer in 2 decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

190 Determine the magnitude of Q if the particle is in equilibrium given that 0 = 32.3° and P = 0011.png 7 F 24 A Round off ONLY on the FINAL ANSWER expressed in 3 decimal places. Add your answer
Solve and show solutions. Figure 01 below. (Subject: Fluid Mechanics)
The reaction at the support A and B is?
Mato 1
If you decide to help, please help with all the parts of the question, I'm not sure I understand any of it... :/ The tank shown in the following figure is being filled by Pipes 1 and 2. The water level is to remain constant. A tank of water is open at the top. The tank is filled from above by pipe 1 and pipe 2. Pipe 1 has diameter d1 = 1 in., and fills the tank with water at a velocity of V1 = 2 ft/s. Pipe 2 has diameter d2 = 1.25 in., and fills the tank with water at a velocity of V2 = 1.4 ft/s. Water empties from the bottom of the tank through pipe 3. Pipe 3 has diameter d3 = 1.5 in., and empties water from the tank at an unknown velocity V3. (a) What is the volume flow rate (in ft3/s) of Pipe 1? (b) What is the volume flow rate (in ft3/s) of Pipe 2? (c) What is the volume flow rate (in ft3/s) of water leaving the tank at 3? (d) What is the cross-sectional area (in ft2) of flow for Pipe 3? (e) What is the average velocity (in ft/s) of the water leaving the tank?
The figure belows shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage, with L₁ = 3 ft, L₂ = 0.5 ft, and L3= 1.25 ft. The densities of the oil and mercury are 55 and 845, respectively, each in lb/ft³. Let g = 32.2 ft/s². Pgage = i Pressure gage lbf/in.2 Air Determine the reading of the pressure gage, in lbf/in.2 (gage). Oil (p=55 lb/ft³) Pam Mercury (p=845 lb/ft³) g=32.2 ft/s²
USE DOUBLE INTEGRATION METHOD TO ANSWER THE PROBLEM. The given figure is a hollow steel tube to be used as a beam. Determine the self-weight (dead load) per meter. 50 mm D. 250 mm 750 mm 35 mm
Problem 10.28 Consider the channel shown in (Figure 1). Suppose that a = 370 mm, b = 210 mm, c = 50 mm. Figure 1 of 1 Part A Determine the location of the centroid of the channel's cross-sectional area. Express your answer to three significant figures and include the appropriate units. y = Submit Part B li μА Ig' = Value Submit My Answers Give Up Units Determine the moment of inertia of the area about this axis. Express your answer to three significant figures and include the appropriate units. μА Value Units p My Answers Give Up ? ? Provide Feedback Continue
Solve please
show complete solution
Reynold's number is used to determine the type of flow pattern through a pipe. It is defined by the equation where ρ =density, μ = viscosity, V = velocity, D = diameter of pipe. Perform a detailed UNIT ANALYSIS to determine the unit of Reynold's number. State your answer in a complete statement.
hour. Work directly in the units of nautical miles and hours. SITUATION 5. The velocity of a particle which moves along the x-axis is given by v = 2 − 4t + 5t³/2, where t is in seconds and v is in meters per second. Evaluate the position x, velocity v, and acceleration a when t = 3s. The particle is at the position xo = 3m when t = 0. STTILATION TI.