Thin tube (20 mm inside diameter, 1 mm wall thickness and 100 mm long) is subjected to an internal pressure of 10 MPa as shown in Figure 1. If the uniaxial creep behaviour of the material is described by Equation (1), determine the increase in the diameter and length of the cylinder after 10th. (Neglect end effects). ɛ° = 2.5x10loʻrº4 . (1) D

Thin tube (20 mm inside diameter, 1 mm wall thickness and 100 mm long) is subjected to an internal pressure of 10 MPa as shown in Figure 1. If the uniaxial creep behaviour of the material is described by Equation (1), determine the increase in the diameter and length of the cylinder after 10th. (Neglect end effects). ɛ° = 2.5x10loʻrº4 . (1) D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The extruded plastic shape has dimensions of D = 37 mm, d = 33 mm, a = 96 mm, and t = 6 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 315 N. (b) If the allowable shear stress for the plastic material is 1350 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 22 mm, d = 20 mm, a = 92 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point. A for a shear force of V = 330 N. (b) If the allowable shear stress for the plastic material is 500 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? D d Answer: (a) TA = (b) V= kPa N
The extruded plastic shape has dimensions of D = 38 mm, d = 36 mm, a = 80 mm, and t= 4 mm. (a) Determine the magnitude of the horizontal shear stress at pointA for a shear force of V = 340 N. (b) If the allowable shear stress for the plastic material is 2300 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? A Answer: (a) TA = kPa (b) V= N
A hollow steel shaft with an outside diameter of 135 mm and a wall thickness of 12 mm is subjected to a pure torque of T = 5,100 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax= (b) dmin = i IN MPa mm
The extruded plastic shape has dimensions of D = 31 mm, d = 29 mm, a = 97 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 375 N. (b) If the allowable shear stress for the plastic material is 1700 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
The extruded plastic shape has dimensions of D = 26 mm, d = 20 mm, a = 85 mm, and t = 8 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 30 N. (b) If the allowable shear stress for the plastic material is 900 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion?
A hydraulic punch press is used to punch a slot in a 0.55-in-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force Prequired to punch the slot. Assume d= 0.50 in. and a= 2.75 in. d Plan view of slug Punch Plate Slug Answer: P = kips
Quest.
The extruded plastic shape has dimensions of D = 27 mm, d = 21 mm, a = 82 mm, and t = 4 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 335 N. (b) If the allowable shear stress for the plastic material is 2150 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? a N Answer: (a) TA = (b) V= tık kPa N
I need this Answer at half time Quickly. Please
A hollow steel shaft with an outside diameter of 145 mm and a wall thickness of 19 mm is subjected to a pure torque of T = 4,800 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: MPa h mm (a) Tmax= (b) dmin =
The extruded plastic shape has dimensions of D = 27 mm, d = 23 mm, a = 100 mm, andt = 3 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 390 N. (b) If the allowable shear stress for the plastic material is 2450 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? d a Answer: (a) TA = kPa (b) V =