The two square-jaw grips have the dimensions shown in the figure and are made of mild steel. The clutch is designed to transmit a power of 1.8 kW at 600 rpm. Calculate the surface pressure and shear stresses on the wedges and jaws. they all in mm

Q: An elevator type lift is being designed to raise a load up to 5,000pounds between floors. Two…

A: Load to be raised : 5000 pounds Diameter of the screw threads 1.5 in Weight of the elevator is 800…

Q: If the inertia is 80 lb-ft2, and the speed of the driven shaft is to be increased from 0 to 1500 rpm…

A:

Q: A multiple-disk clutch is to operate in oil and be able to transmit a design overload torque of 800…

A: Given:T = 800 N-mDo = 150 mm = 0.150mDi = 90 mm = 0.09mpmax =1000 kPaf = 0.10To findTotal number of…

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: Determine the given question with correct solution

A: Given data; P=25 KW=25×103 WN=300rpmp=85 KN/m2=0.85 N/m2d2=380 mmr2=190 mmn=2μ=0.25 Find,1.outer…

Q: THE ENGINE OF AN AUTOMOBILE IS RATED TO GIVE SOKWAT 200 RPM WITH A MAXIMUM TORQUE OF 600 N-M. DESIGN…

A: The answer is mention below

Q: 112 he Ratio between the Outside and Inside Diameter of the Disk is 100 the coefficient of friction…

A:

Q: mm, The semi-angle of the cone is 15°. The coefficient of friction is 0.3. Find the torque required…

A: A disc or plate clutch has the same use that a cone clutch has. Instead of two spinning discs, the…

Q: Solve and show solution for answer

A: Step 1: Step 2: Step 3: Step 4:

Q: 4.) A flat belt makes contact with an 18 in. diameter pulley through half its circumference. If the…

A:

Q: Two identical 4 in. major-diameter power screws (single-thread) with modified square threads are…

A: Given:f = 0.1fc = 0.24v = 3ft/min = 36 in /minTo find:Power required to drive each screw when the…

Q: A single plate cutch consists of one pair of contacting surfaces. The inner and outer diameters of…

A: Given Data Inner diameter of clutch is: di=100 mm=ri=50 mm Outer diameter of clutch is: do=150…

Q: A disc clutch is required yo transmit 5 kW at 2000 rpm with coefficient of friction 0.25 and bore…

A: Given                      Power, P = 5 kW Coefficient of friction = 0.25  Constant pressure, P = 1…

Q: Perform "Design for stress" based on Machine Component Design knowledge

A: An introduction for the solution is:The answer begins with mechanical design principles, which are…

Q: Specify the required torque M on the power screw necessary to overcome a resistance of 490 N to…

A:

Q: 3 The press shown below has a rated load of 25 kN The twin screws have Acme threads, a diameter of…

A:

Q: A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion…

A: Friction Clutch Friction clutch is used to transmit the power in shafts and machines which must be…

Q: =ust is carried on a collar of 100 mr er and 60 mm inner diameter. The ficient of friction at the…

A:

Q: The effective pressure on a 400 mm diameter piston is 1.1 MN/m² when the crank is 32° beyond top…

A: Given: Diameter of the piston→D=400 mm=0.4 m So area of the piston→A=π4×D2=π4×0.42=0.125 m2 Pressure…

Q: solve show solution for answer given

A: Answer:Explanation:

Q: A multiple disk clutch consisting of 3 disks on the driving shaft and 2 disks on the driven shaft is…

A:

Q: The figure shows an internal rim-type brake having an inside rim diameter of 11 in and a dimension R…

A: Brake is a mechanical device which absorbs energy from the moving system or any mechanism with the…

Q: The disc clutch has a pair of mating friction surfaces, with an outer diameter of 350 mm and an…

A: Given data:- outer diameter=350 mm inner diameter =250 mm The average value of the coefficient of…

Q: In a thrust bearing, the external and the intermal diameters of the contacting surfaces are 320 mm…

A:

Q: A 5/8-11 unc x1.75 long grade 8 bolt clamps an assembly as shown. A total load (P)of 11500 lbs is…

A:

Q: Calculate the torque.

A: The applied force is F = 89 cN = 0.89 NLength of crowbar L = 0.7angle = 80 degreeTorque is defines…

Q: The clutch of a motor car is required to transmit 9 kW at 3500 rpm. It is of single-plate type, with…

A: Given: The power of the motor is 9 kW. The coefficient of friction is 0.25. The maximum pressure is…

Q: Two pulleys with diameters (450 mm) and (200 mm), centre distance (1.95 m). if we use cross belt…

A:

Q: to calculate the radial force acting upon the clutch face, shouldnt the force of 1 shoes be…

A: Yes, as per your followup question, net outward force exerted by each shoe is evaluated and then…

Q: ch. The friction lining has a ce 25. The bore radius of friction li ilom contLacl pressur of IMI

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.