The switch was shown in Figure 11-36. opened for a long time and closed at t= 0, find the currer

Q: . What is the highest decimal munher that can be represented by each of the following nanbers of…

A:

Q: Figure Q1b shows the voltage and current waveforms from an AC circuit. A student states that these…

A: Different types of AC circuit shown below. Fig.-1 It represents a Pure resistive circuit. In pure…

Q: If a MOSFET is to be used in the making of logic gates application then it must work in O a.…

A: MOSFET should operate in cut-off and linear regions when used in logic gate applications. Because…

Q: Consider the circuit shown in the figure below with R1=16 kQ and R=8 kQ The Zener diode voitage is…

A: Zener diode is turn on when voltage when voltage across it exceeds the 3.5 volts. as zener diode is…

Q: What is the equation of KVL at loop A-C-D-A, C-B-D-C, and A-D-B-A.?

A:

Q: b) Draw the result signal for the following figure? 10 v m(t) = 0

A: to draw the result signal for the following figure

Q: Q: Draw output voltage waveform for this circuit if ß-50. +10v +5v -1vF Vi 2 3 4 t(ms) Vi AC 50k…

A: We need to find out output voltage for given circuit

Q: What will be the branch voltage when Rx is adjusted to 162? What is the magnitude and direction of…

A:

Q: 1-) I 4+7 i solve the complex number 2.) 5+ 3i transform to rtan dard Form

A:

Q: What will be the branch voltage when Rx is adjusted to 162? What is the magnitude and direction of…

A: Given, A network has given. We have to find the current and it's direction in Rx branch. Current…

Q: Can you please circle ⭕️ the answer of questions C and F BECAUSE ITS

A: Need to find the root locus on the real axis and the angle of departure.

Q: If the following voltages are measured in T2, the probable fault is 1:1 S1 7.5 V 15 V S2 7.5 V T2 O…

A: When any partial short is there in the circuit, then the total voltage that appears across the…

Q: choose the correct answer.

A: In this question we will find unknown current using kCL....

Q: R=8 2 Ry=12 2 Re=10 2 Is E, 100 V Rp RE E, 120 V 15 2 20 2

A:

Q: ****** For the following circuit, the vo waveform is Plo 2 LV F - (+V) to Correct Wrong O

A: In this question,  We need to choose the correct option Assume diode is ideal.  So forward bias…

Q: A 60-Ohm resistor and a 20-Ohm resistor are connected in series across a 50 V dc source. What is the…

A:

Q: An inductor has an inductance of 4H. It is connected in series with a resistance of 180. It is fed…

A: In this question, We need to determine the current after t= 94s of switch close. If An inductor has…

Q: the secondary coil is 200 A with a 500 turns. there are 1000 turns on the primary and we need to…

A:

Q: Determine the magnitude and sense (direction) of the current in the 10-22 resistor when I = 1.8 A.…

A:

Q: Im not sure if i am correct. I dont have any way to check my answers. Does this circuit not work…

A: The circuit can be analyzed by verifying the elements in the circuit that are open-circuited. The…

Q: 8 Is 4H 152 152 + r. I Find VAIVES MAKE THE CIRCUIT STABLE the PANGE of THAT will FOR P

A:

Q: B = 0.25 T to the right l = 2 m i = 1.5 A Figure 2(c)

A: We need to find out force on current carrying wire placed in magnetic field .

Q: Draw a circuit/schematic diagram for a variable 0-5V power supply and a (+)15V-0V-(-)15V power…

A: Circuit diagram of 0-5V power supply

Q: What will be the branch voltage when Rx is adjusted to 162? What is the magnitude and direction of…

A:

Q: Check the observability and controllability of the following systems: 2 1 07 9-68-30 .x2 002 X3 02…

A:

Q: What type of signal does the circuit in Figure 6 produce? Determine the frequency of the output.

A: The type of signal received at the output of the circuit needs to be obtained and the frequency of…

Q: 98 With the measurement terminal open-circuited, the infinity reading of a megger is due to Ocurrent…

A: Given  With the measurement terminal open-circuited, the infinity reading of a megger is due to...

Q: 50. The waveforms in Figure 6-81 are observed on the inputs of a 74HC1518-input multiplese Sketch…

A: Multiplexers: It is a data selector whenever enable is high (1) otherwise it produces output as…

Q: Is it possible to view multiple waveforms at the same time?

A: As per Bartleby guidelines we are allowed to solve only one question, please ask the rest again.

Q: what is the Q point

A: Given Data: R1 = 10k R2 = 2.2k Vcc = 25 V RE = 1k Rc = 3.6 k

Q: Design a clamper circuit with the below waveform:

A: The output waveform is shown below:

Q: In transformer, the power will with increase in voltage. O increases O decreases O remain same O be…

A: Transformer current and voltage ratio  V1/ V2 = N1 /N2 V1/ V2 = N1 /N2  AND        I1/I2 = N2 /N1…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.