The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 10 mm*). For the loading shown, determine the beam deflection Vc at point C. Assume P = 69 kN, w = 19 kN/m, LAB= LBC= 3.5 m, LcD= 1.8 m. LAB LBC LCD mm. Answer: Vc=

The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 10 mm*). For the loading shown, determine the beam deflection Vc at point C. Assume P = 69 kN, w = 19 kN/m, LAB= LBC= 3.5 m, LcD= 1.8 m. LAB LBC LCD mm. Answer: Vc=

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

* Given the FLEXURAL RIGIDITY of the beam shown=6000 KN.m^2, find the deflection :at the roller support 50 kN B C A 2m 3m D 3m Non of them O No deflection O -0.025 m O +0.025 m O +0.125 m O -0.125 m O
Given the Cantilever beam loaded as shown, determine the deflection of the beam at the right end by using Three Moment Equation (TME). Note: The unit obtained from TME for EIy is kips-ft^3.
Using Castigliano’s Theorem, determine the deflection equation for the cantilever beam shown below and evaluate the deflections at point B and point C.
Draw the free body diagram, shear force diagram, and bending moment diagram for the beam shown below and calculate values at each point:
Use moment area method. Give me clear calculations
Consider the beam in the picture below: 7kN/m 5kN/m P N/m Section 1 Section 2 Section 3 - L/3 L/3 L/3 %3D Take P = the last four digits of your student number in N/m. If P<250 N/m then take P = 30OON/m instead. Take L = the third digit of your student number, reading left to reight. If this value is zero then take L = 2 Assume: The reaction at the Pin = V pin 47000L+9PL )N 54 The reaction at the Roller = Vroller = 61000L+9PL 54 and that both reactions act vertically upwards. a) Find an expression for the internal moment for Section 1. Show all working and any relevant free body diagrams. b) What is the maximum magnitude of the internal moment for Section 1? Mark sure you prove that the value you calculate is the maximum. c) Find an expression for the internal moment for Section 2. Show all working and any relevant free body diagrams. d) What is the maximum magnitude of the internal moment for Section 2? Mark sure you prove that the value you calculate is the maximum. e) Find an…
Problem 2 (30 points): The formula for the deflection of the beam shown is: Wo y(x) = (-x5 + 5Lx-10L?x3 + 10L³x²) 120LEI Wo 15 x 107 N L = 2m %3D max m E = 7 × 1011 N m2 I = 6 x 10-4m Use the Newton-Raphson Method to determine the x location along the beam where the deflection is y(x) = 0.14 m. Use a starting guess of xo 1.2 m. Be sure to show your %3D calculation for the derivative of the function and your calculations you use to fill out the table. You only need to perform two iterations of the method, which means you should fill out the table below. Notice that y is defined as positive in the downward direction, which means that both the function and the target deflection are positive values in the coordinate system. y(xn) y'(xn) Xn+1 Step Xn 2.
Given the beam and the loading shown below, if L = 5 m, W1 = 4.5 N/m and w2 = 22.3 N/m. Calculate the vertical reactions at the supports. W2 w(x)=w, +ax³ L A B X Reactions: Ay = 单位 (tolerance 0.5 N) By = |数字单位 (tolerance 0.5 N)
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
The simply supported beam consists of a W14 x 34 structural steel wide-flange shape [E = 29,000 ksi; I= 340 in."1. For the loading shown, use discontinuity functions to compute (a) the slope of the beam at E and (b) the deflection of the beam at C. Assume wo = 10 kips/ft, wCD = 7.0 kips/ft, LAB = 7.0 ft, LBc = 7.0 ft, LCD=9.5 ft, LoDE = 4 ft. Wo WCD C E LAB LBC LCD LDE Answer: (a) 0g = rad (b) vc = in.
The cantilever is subjected to a point force "P" in the middle of the beam span. The beam's modulus of elasticity, E-200 GPa and moment of inertia, l= 6x10^6 mm^4, are the same at every point. Accordingly, in which option is the maximum deflection (vertical displacement) in the beam given in "mm"? P= 12 kN, L= 2.8 m.
Required Ihmai -- Q4/ A curved beam of a round cross section is shown in figure 3. The beam is made of a plain carbon steel 3OC8 (oy = 400 N/mm2) and the factor of safety is 3.5. Determine the dimensions of the beam Q4/* kN R= 4D Figure 3 ×ト kN O D= 21.53 mm D = 19.03 mm O D= 20.10 mm 23.30 m