The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well a Live Load of (2 kNm) is simply supported on three concrete beams of dimensions (300*500)mm that, in turn, are supported by two concrete girders of (300*600mm), (each girder is support on two columns) as shown in Fig.1. Determine the loads acting on beams BE and AD and girder AC. (concrete density: Let Yet 24 kNm) Concrete Girder (300*600mm 10 m Concrete floor beam (300 500mm 5m Fig. (1)

The precast floor system consists of a 150-mm-thick concrete slab carry its self weight as well a Live Load of (2 kNm) is simply supported on three concrete beams of dimensions (300500)mm that, in turn, are supported by two concrete girders of (300600mm), (each girder is support on two columns) as shown in Fig.1. Determine the loads acting on beams BE and AD and girder AC. (concrete density: Let Yet 24 kNm) Concrete Girder (300*600mm 10 m Concrete floor beam (300 500mm 5m Fig. (1)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is inclined I V: 4 H and distance between trusses is equal to 6 m. The purlin has a weight of 79 N/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 720 Pa, live load of 1000 Pa and wind load of 1.2 1.2 1440 Pa. Coefficient of Purlins pressure at leeward and windward are 0.6 and 0.2 respectively. Assume all loads passes through the centroid of the section. Truss Properties of C 200 x 76 mm Sx = 6.19 x 104 mm Sy = 1.38 x 104 mm W = 79 N/m 12 12 1.2 I Allowable bending stress Fbx= Fby = 207 MPa Truss %3D 6m O Calculate the bending stress, fox, for dead load and live load combination (D+ L). Calculate the bending stress, foy, for dead load and live load combination (D + L). O Calculate the maximum ratio of actual to the allowable bending stress for load combination 0.75 (D + L + W) at the windward side. fbx = 151.14 MPa fby = 169.6 MPa Interaction = 1.25
a) The floor system shown is subjected to a total uniform distributed load of 12 KN/m². Sketch the loading that acts along the members DE and BDG. -2.0 m - 3.0 m- A 3.0 m D E 5.0 m F G
Determine end reactions for Beam B-1 and Girder G-1. B-1 1 F1 • L1= 24 ft L2= 6 ft Live load 30 psf 4" Thick concrete slab (density = 150 pcf) . 5/8" Thick terrazzo (12 lb/ft2/in) • Beam weight = 35 lb/ft . Girder weight = 26 lb/ft Please round to the nearest one. One end reaction for B-1 = lbs One end reaction for G-1 = lbs Please answer all parts of the question. 20 DOO 000 F2 @ 2 JAL #3 G-1 F3 54 $ F4 % 5 F5 L2 L2 L2 L2 MacBook Air F6 A 6 & 7 F7 11 ► 11 * 8 F8 F9
Determine collapse load Wu for continuous beam ABCDE loaded and supported as shown in figure . For span AC plastic moment of resistance is 50 % more than that of CE .
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs./ft'. and the uniformly distributed live load L- 50 lbs/ft². L-22 B. Girder G1: - B [za] 12' GI GI 12 + [ial FIG. 1-Steel Floor Beam a) Strength - Bending and Shear -I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [za]
span of beam af is 6 meters. Thank you.
Reinforced concrete design plz answer the a and b with complete solutions.. thank you
Question 29 The laminated beam, shown in cross section, is composed of ?ve 6- in. by 2-in. planks that are glued together. The beam carries a uniformly distributed load of intensity we over its 8-ft simply supported span. If the working stresses are 75 psi for shear in glue, 90 psi for shear in wood, and 8ø0 psi for bending in wood, + 6 in. 1. determine the maximum allowable value of we so that the shear stress in the wood is not exceeded. A. 900 lb/ft C. 833 lb/ft determine the maximum allowable value of we so that the shear B. 555 lb/ft D. NOTA 2. stress in the glue is not exceeded. A. 900 lb/ft C. 833 lb/ft B. 555 lb/ft D. NOTA 3. determine the maximum allowable value of we so that the bending stress in the wood is not exceeded. А. 900 lb/ft В. 555 lb/ft C. 833 lb/ft D. NOTA 5 @ 2 in. = 10 in. –
The floor structural system shown in Fig 1 comprise W-section steel beams and girders supporting a 5-inch thick concrete slab which provides full restraint to the flanges of the beams. The density of concrete is 150 lbs. /ft³. and the uniformly distributed live load L=50 lbs/ft². L-22¹ B B. Girder G1: - [82] 12' Gl GI [BI] FIG. 1-Steel Floor Beam a) Strength - Bending and Shear 12' + I 1) Produce a sketch of the floor plan showing the tributary load distribution areas for the beams and girders [zul
A concrete floor slab measuring 6 m x 3 m is simply supported on one side brick load bearing walls along the 6 m sides. The concrete slab is 200 mm thick and reinforced at the bottom as follows.1. Main reinforcement (short span i.e the bars are parallel to the short span), Y 12, shape code 34 @ 125 mm centre to centre,2. Distribution reinforcement (long span i.e the bars are parallel to the long span), Y 10, shape code 20 @ 300 mm centre to centre,3. Concrete cover, 30mm,4. Concrete strength, 40MPa.Draw the reinforcement layout for this slab, in plan and section, indicating all the reinforcement and necessary information required by the contractor. You must calculate and indicate the number of bars required on your drawing. You do not need to calculate the bar lengths and the curtailment. Your drawing must be neat.