The potentiometer used in audio system is having a total resistance of 10K2 with maximum length of 8cm and supplied with 12V DC power supply. After the application of displacement, the wiper moved from 1.5cm to 4.5cm. Then |calculate the following, i. Sensitivity of the Transducer in volt/cm. ii. Change in resistance of the transducer. iii.Output voltage of the transducer. iv. Output voltage, when the wiper is moved to Ocm.

The potentiometer used in audio system is having a total resistance of 10K2 with maximum length of 8cm and supplied with 12V DC power supply. After the application of displacement, the wiper moved from 1.5cm to 4.5cm. Then |calculate the following, i. Sensitivity of the Transducer in volt/cm. ii. Change in resistance of the transducer. iii.Output voltage of the transducer. iv. Output voltage, when the wiper is moved to Ocm.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Which of the following can be used in amplifier circuits? а. Photodiodes b. Transistors C. Zener diodes d. Rectifiers
A group of UTAS-Nizwa students are working on a project entitled "Gas leak detector alarm" for their final year in Diploma level. The circuit works on DC voltage of 16 volts and DC current of 7 milliampere. Students need to design a power supply circuit for their project. Consider an RMS voltage input of 220 volt, 60 Hz. Using a Full Wave Bridge Rectifier with Transformer, Silicon diode and Capacitor Filter, Design the power supply. a. Compute for the load resistance, peak output voltage, input peak voltage to the diodes (secondary voltage), peak input voltage and the turns ratio of the transformer. 1. What is the value of the load resistance? b. Draw the Power Supply circuit (capacitor filter connected in parallel with the resistor) and write the computed values (No value for the capacitor).
An oscillator employs .................. feedback 1. Positive 2. Negative 3. Neither positive nor negative 4. Data insufficient
Answer the following questions about Digital to Analog Converter (DAC): 1. Write its definition. 2. Draw its block diagram.
describe and compare the different types of Analog to Digital Converters(Advantages, Disadvantages, Max Resolution, Max Sample Rate and Main Applications). Note: Please do not handwriting and write an average information for each type.
(1) Determine the output voltage of the DAC (digital-to-analog converter) if the input is 001101001111 (ii) If the monitoring unit was set to display a maximum of 5000 liter with the reference voltage, predict the digital input which is required to display 1500 liter. (iii) Determine the smallest output change.
An oscillator employs .................. feedback 1. Positive 2. Negative 3. Neither positive nor negative 4. Data insufficient
Consider two amplififiers with the following parameters: Amplififier A: Gain = 20 dB; Noise ratio, NR = 1.05 Amplififier B: Gain = 20 dB; Noise ratio, NR = 4.1 Identify the amplififier that adds the least internal noise to the input signal and determine its noise fifigure in dB.
Solve both questions please and don't copy I need answer to understand don't copy it from goggle or somewhere else . Thankyou A 'T' type thermocouple has linear calibration between 0 °C and 80°C with voltage at maximum temperature, with reference junction at 0 °C, equal to 25.66 mV. i) Determine the correction which must be made to the indicated voltage when cold junction temperature is at 15 °C. ii) If the indicated voltage is 4.4 mV, find temperature at hot junction.
1) Write 100µ Sec delay segments using •a) 100 kHz oscillator (Clock Frequency is 100KHz). •b) 4 MHz oscillator (Clock Frequency is 4 MHz). •c) 16 MHz oscillator (Clock Frequency is 16 MHz). •d) 32 MHz oscillator (Clock Frequency is 32 MHz). 2) Write 1mSec delay segment for 4 MHz oscillator. Show your calculations and your code
establish a relation between the current amplification factor of CC and CE mode
Q1) assume A/D converter of counter type uses clock with 100 kHz counter of 8 bit A)determine the total conversion time B)determine the conversion time that is required to generate the sample (111110000)