The piston shown in the figure is held in equilibrium by 210 kPa pressure of gas at flowing at III. Given the diameters for the piston as shown, with PI = 350 kPa, and PII = 130 kPa. Determine (a) the cross-section at I, II & III in m2 (b) the weight and mass of the piston in N and in kg respectively, considering that the contacting surfaces are frictionless.

The piston shown in the figure is held in equilibrium by 210 kPa pressure of gas at flowing at III. Given the diameters for the piston as shown, with PI = 350 kPa, and PII = 130 kPa. Determine (a) the cross-section at I, II & III in m2 (b) the weight and mass of the piston in N and in kg respectively, considering that the contacting surfaces are frictionless.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An air receiver carries a pressure of 3500 kPa absolute @ a temperature of 25 C. A fire occurs near the receiver which causes the temperature to rise to 80 C. Neglecting the increased volume of the receiver due to expansion, calculate the air pressure at this temperature.
Show complete solution
Determine the pressure of Gas 2. Follow the statement and the figure below. Apply Knowledge about Fluid Mechanics to solve the question.
The test tube opens at 293 K with 15 cm Hg at the bottom, and 7.5 cm of water above the Hg. Calculate the pressure at the bottom of the tube if the atmospheric pressure is 760 mm Hg. Use the density of 13:55 g / cm3 for Hg and 0998 g / cm3 to air.Berikan answers in terms of dyne / cm2,psia, and kN / m2 • (see conversion table). a. … KPa. b. … Dyne / cm2. c. … Psia.
Cords are loop around a small spacer separating two cylinders each weighing 400 kg and pass, as shown in figure over a frictionless pulleys to weights of 200kg and 400 kg. Determine the angle and the normal pressure N between the cylinders and the smooth horizontal surface. 200kg Total W = 800 kg 400kg
Determine the height h of the column of mercury in the tube if the level of water in the tube is 0.2 m and the dimensions of the oil and the water listed in the diagram. Let poil = 900 kg/m³, pwater = 1000 kg/m³, PMercury = 13,500 kg/m³. A 0.4 m Oil B 0.3 m h Water Mercury 0.2 m
▼ The bent plate is 1.6 m wide and is pinned at A and rests on a smooth support at B. The fluid is water. Pw 1000 kg/m³ (Figure 1) Figure Part A 1m 4 m A₂ = 78.5 Part B A Ay = -2 m- Determine the component of reaction at A. Express your answer to three significant figures and include the appropriate units. μA Submit Submit Previous Answers Request Answer 3 m- μA KN X Incorrect; Try Again; 9 attempts remaining Value B Request Answer Determine the y component of reaction at A. Express your answer to three significant figures and include the appropriate units. posso 1 of 1 KN ? S ?
- Two cylinders M and N rest in a channel as shown in figure. The cylinder M has diameter of 6 cm and weighs 200 N, whereas the cylinder N has diameter of 8 cm and weighs 500 N , determine the pressure at all the four points of contact ?
Air is contained in a frictionless piston-cylinder assembly as shown below. The initial equilibrium position is subjected to atmospheric pressure of 100 KPa. The mass of piston and weight together is 200 kg. The piston has a diameter of 0.452 m. The initial temperature of the gas in the container is 800 K. Take C, = (7/2) R and Cy = (5/2) R, calculate the following: (a) force exerted by the piston, weight, and the atmosphere in N (b) total pressure of air in the container in kPa (note: at initial equilibrium position, the Peas = Pop) (c) total moles of air in the container (assume air behaves ideally)
The cylinder, which has a sensitively moving piston inside, is filled with V₁ = 0.93421 The temperature outside is T₁ = 8 °C and the air pressure is p₁ = 101 kPa The piston is quickly pressed into the cylinder, causing the volume in the cylinder to decrease to V3 = 0.2975 1 and the pressure to increase to p2 = 210 kPa. The piston is locked in place and the cylinder is immediately brought to the laboratory. After that, it happened that the gas temperature became same as the laboratory temperature of T3 = 22 °C Determine the gas pressure when the gas temperature has reached the final temperature of the laboratory. What is the algebraic expression for pressure in terms of V_1, T_1, p_1, V_3 and T_3 P3 = What is the pressure? P3 = kPa