The number of revolutions of a current meter in 40 s time was found to be 12 and 30 when the velocity of flow was 0.3 and 0.5 m/s respectively. What velocity would be indicated by 30 revolutions of the current meter in 50 seconds.

Q: a. What are the characteristics of Hydrograph?

A: As per our guidelines we answer one question .Kindly resubmit the question for second part solution.…

Q: ) List three uses of water in architecture.

A: Introduction: This question comes from Environment Civil engineering. Water is the main important…

Q: Calculate the area of ​​the shaded figure below

A: In the construction process, a plan of field or site is provided by the client to the contractor.…

Q: Q2: The table below represents the vertical coordinates of the hydrograph of a rainstorm over a…

A: Given data:- Mountain area, A=770 km2 Below table is given; 72 66 60 54 48 42 36 30 24 18 12 6 0…

Q: 16 10 14 D

A: Use Pythagoras theorem

Q: Find the missing rainfall (in mm) at station X. (given data are in mm) Rain gauge Normal Actual A…

A:

Q: Describe the Procedures and equipment needed for obtaining water samples below the water table.

A: The different parameters like ph, turbidity and many more are checked with different procedures and…

Q: How to conduct an analysis of a water discharge

A: Solution: Analysis of water discharge is done in order to ensure the discharge standards are being…

Q: Which direction will water flow on the diagram below? Is this a positive or a negative direction? h₁…

A:

Q: Distance from bank Width of Velocity at point Meter Revolutions Time Mean () Depth qns section Area…

A: Given data: Observations of current meter.

Q: How many cubic meters of water

A: Conservation of mass states that total inflow of water is equal to total outflow at a junction.

Q: Question 6 6. To find the distance across a small lake, a surveyor has taken the measurements as…

A:

Q: A circular water tank with a diameter of 10 m and with uniform cross section , some angles…

A: Diameter of circular tank = 10m MB is at the center of bottom base. Zenith angle = 1400

Q: Define the difference between standpipe, standpipe piezometer and piezometer?

A: standpipe : this is a elevated  vertical pipe and filled with water for producing pressure and water…

Q: Im Im 0.6m Im Im 3m 2.

A:

Q: Background: Water towers are elevated water storage construction that are built at a certain height…

A: Given, PHouse = 350 kPa μH2o= 1.002 Nsm2ρH2o = 998.2 kgm3e= 0.0015 mm

Q: Given the map on the right of an area, you are tasked to suggest the possible location of a well to…

A: The well must be constructed in the dark blue region where, there is enough water available and can…

Q: For determining the discharge of a river, the following observations were taken across the river.…

A: The ground elevation ( Reduced level ) of right bank at point 9 = 43.765m The water level of river…

Q: Complete the table below. STATION BM1 A B C D E F BM2 BS 1.548 1.423 2.522 2.883 2.779 1.272 Highest…

A: Given Data: To Determine: Highest elevation of line of sight. Station with highest elevation Lowest…

Q: Calculate the sprinkler system capacity from the following data: Number of laterals in the main = 3…

A: Given, Number of laterals= 3 Length if each lateral = 12m Spacing between the sprinkle St=12m Water…

Q: ain the conversion of Precipitation into Stream flow using flowchart.

A: Follow the next diagram for details

Q: How are we gonna design the height of the earth-fill dam from the ground? For example, We are…

A: The dam's height is the vertical distance from the natural streambed at the dam's downstream toe to…

Q: Describe average discharge velocity.

A: Velocity is defined as the rate of change in distance covered by a body or object. Flow velocity is…

Q: (Engineering fluid ) How are head loss and slope related for noun uniform flow, as compared to…

A: Non-uniform flow-Non-uniform flow is a flow when the velocity of flowing fluid changes at different…

Q: draw the layout of the custom pumping system, labeling all components

A: It is a bulk of pipe which used to flow the liquid from one place to other

Q: 1. COMPUTE THE VELOCITY AT A DISTANCE OF 20.5 m FROM THE FIRST POINT 2.COMPUTE THE DISCHARGE IN…

A: Since the question number to be solved is not specified, the solution for Question No.01 is as…

Q: The following are recording gauges except for: A Natural Siphon Type B symon's Gauge Weighing bucket…

A: Ans (1) Option (D) is correct Normal rainfall data is the average data of last 30 years which gets…

Q: Situation 16 - The flow of water from Reservoir A shown is 600 L/s. Properties of the system are as…

A:

Q: Q- There are four rain gauge station existing in the catchment of a river. If means rainfall is 500…

A: Given data- 4 rain gauge stations- Rainfall P=500 mm, Standard deviation- σ=120, Allowable % error…

Q: How the process of pumping large volumes of water from a well does can alter the position of a…

A: -  The process of pumping large volume of water from the ground at a fast rate in comparison to rate…

Q: Calculate the correct point A, if the staff re instrument which is s from

A:

Q: What is the shape of a perpendicular cross section of a horizontal trough of constant cross section…

A: Horizontal trough are of many shapes

Q: 17 What is the shape of a perpendicular cross section of a horizontal trough of constant cross…

A: Horizontal trough of many shapes as listed below

Q: TABLE Q2(c) 0.0 | 0.6 0.0 | 0.3 6.0 | 6.6 1.29 2.16 | 2.55 | 2.22 | 1.68 | 1.41 | 1.05 | 0.63 | 0.42…

A: Given: 1. Distance (m) 2. Depth (m) 3. Velocity at 0.2 depth (m/s) 4. Velocity at 0.8 depth (m/s)…

Q: Compute the height of a building (in feet), given the following data: • Instrument Height = Rod…

A: Horizontal Distance to Prism, D = 142.68 feetThe Zenith Angle, The zenith angle is the angle…

Q: 200mm 300mm diameter 450mm 30° 400mm 1 Mercury diameter (SG = 13.6 "X" 350mm Water ameter vertical…

A:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?