The length instruction used to find the number of elements True False

Q: After the SHR instruction is executed in the code sequence below, what is the final value for AL?…

A: Correct Option is B⇒ 0010_1011

Q: A- Write the equivalent code for THREE of the following instructions: 2- LES SI, [start] 1- XCHG CX,…

A: 1) XCHG  REG, memory memory, REG REG, REG  Exchange values of two operands. Algorithm: operand1 <…

Q: Select the statements that apply to the use of the CMP instruction CMP src, dst

A: Answer: CMP instruction is used to compare two operands Unlike SUB instruction CMP instruction does…

Q: Using the following data definitions: byte1 BYTE OFFh, 1, 2 byte2 BYTE 14h OFFFFh, 1, 2 word1 WORD…

A: Using the above data definition we need to write instruction which moves the lower 8 bits of word2…

Q: . List down the values of AL for each execution of the LOOP MOV CX, 000AH ;set loop count MOV AL,…

A: Actually, registers are used to store the data/information. there are 4 types of general-purpose…

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB,..etc.) NOTE:…

A: ADD instruction

Q: The instruction that moves each bit to the right, copies the lowest bit into the Carry flag, and…

A: Introduction: Each bit in the instruction is shifted to the right. Rotate Through carrying Right…

Q: As a result of this difference, the LEA instructions are far more powerful than the OFFSET operator.

A: Introduction: It remains to be shown how the LEA command may be more powerful than the OFFSET…

Q: answer all the questions

A: Here we have to answer all the given MCQs

Q: After the ROL instruction is executed in the code sequence below, what is the final value for AL?…

A: The correct option is a.) 1110_0100.

Q: jupyter nootebook python with julia (with JuMP, Clp) 1: Modify your models and coding of Chebyshev…

A: The objective of the question is to solve a linear programming problem using the Chebyshev center…

Q: To protect a loop (using Loop instruction) from starting while CX=0, we use the following…

A: Below I have provided the solution of the given question

Q: Memory element used in sequential circuits * Register Counter Gates Flip-flops Which of the…

A: The sequential circuit is a special type of circuit that has a series of inputs and outputs. The…

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB,..etc.) NOTE:…

A: To the division of unsigned numbers the DIV instruction is used.

Q: Write the machine code of the instruction: subwf 0x53, 1 How to write answer: Write 4-digits…

A: Answer is given below .

Q: Fill in the following table with the correct answers. Show all values in hexadecimal. Initial Value…

A: here i filled it one by on. ================================================================= about…

Q: The following zero-operand instructions (stack machine) are corresponding to the arithmetic…

A: PUSH- PUSH INTO THE STACK POP- POP/STORE IT INY THE VARIABLE STATED OPERATOR(+,-,*,^,/)- POP AND…

Q: Distinguish different types of data dependence among the following instructions. Rewrite the program…

A: Let's understand first what is data dependency. Data dependency or dependency analysis is concerned…

Q: NAME THE INSTRUCTION ONLY that will perform the following function (i.e. ADD,MOV,SUB...etc.) NOTE:…

A: The answer is ADC (Addition with carry)

Q: What function does the ALU perform when instruction "slt" executes?     add     magnitude…

A: ALU or arithmetic-logic unit, is the part of CPU that carries out arithmetic and logic operations on…

Q: The following instruction is valid NOT AL Select one: True False

A: Suppose AL = 1011000 Then NOT AL  = 0100111 NOT reverses the bits in an operand

Q: The decimal number 9510 written as the converted and equivalent hex value equals $66. True False

A: We need to check if the given hexadecimal value of the decimal number is correct or not and whether…

Q: The instruction that can affect the sign flag is no one SAR SHL SAL

A: SAR and SHR are both same kind of instruction. Whereas SAL and SHL are both same kind of…

Q: ASSEMBLY The JBE instruction is used when comparing unsigned integers. True False

A: Given: ASSEMBLY The JBE instruction is used when comparing unsigned integers. True False

Q: To cut a specific part of the drawing, use the instruction Delete Trim Erase Fillet O To draw a…

A: To cut a specific part of the drawing  Trim is used to cut the specific part  Answer is Trim

Q: After the SHR instruction is executed in the code sequence below, what is the final value for AL?…

A: The SHR command is an abbreviation for 'Right Shift'. This command simply moves the bits mentioned…

Q: The destination operand of the IMUL instruction cannot be a memory operand. True False

A: Ans) IMUL instruction is used for signed multiplication of two operand.

Q: 1. Write a complete program to find the absolute value of any number. The program should prompt the…

A: Actually, program is an executable software that runs on a computer.

Q: The program counter (PC) contains the address of the next instruction -pair to be fetched from r a.…

A: EXPLANATION: The program counter(PC) is a register. The function of PC is at the current time, it…

Q: What will be the value of B-register after the following program is executed. Label Mnemonics…

A: Requirements : -

Q: 12- Write a program to count from 0 to 15D using LOOP instruction.

A:

Q: After the ROR instruction is executed in the code sequence below, what is the final value for AL?…

A: ROR:  It stands for Rotate Right It shifts all bits in the register or memory operand specified.…

Q: The TEST instruction performs the. b. OR operation. c. NOT a. AND d. XOR

A: The TEST instruction performs a BITWISE AND on two OPERANTS and  flages-register SF, ZF, PF are…

Q: ased on the diagram below, what is the result for register AL after executing the mnemonic…

A: We are given few instructions and we are going to find out value of AL after instructions execution.…

Q: Write the sequence of micro-operations for each cycles required to execute the instruction JB R1,…

A: Task : Implement subtraction using two's complement method.