The lap joint shown in the figure is fastened by four rivets of 4-in diameter. Find the maximum load P in 1b that can be applied if the working stressesare 14 ksi for shear in the rivet and 18 ksi for bearing in the plate. Assume that the applied load is distributed evenly among the four rivets, and neglectfriction between plates.7/8 in.4 in.0,00

Given: d=34in = 0.75 in τ = 14 ksi σb =18 ksi

Answered: The lap joint shown in the figure is…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cross section of the beam in the figure is made of 100 mm x 20 mm boards. It is manufactured by screwing each other and the distance between the screws is 50 mm. and the shear force is V = 2500 N. Safe slipping for screw material Since the stress value is τem = 50 MPa, the screw that can be used in connection Find the diameter. dimensions in mm
Read the question carefully and give me right solution with clear calculations
Question 1 The same torque is applied to two tubes with identical metal sheets, determine the ratio of T circle/Tsquare of the shear stresses. Given: r= 14 mm, S = 19 mm, and t = 2.84 mm. 43 FETOO KA F1 F2 FS FB F7 F8 ESC T H.
Situation 2: The bar AB is being supported by bars at each end. The length and the area for each bar are given. Determine the distance x to where the 100 N load must be applied if the bars must have the same stress. A. Distance x (feet) L-3 ft A= 0.2 in L=2 ft A= 0.3 in 100 N B. 8 ft
A wooden frame shown below is supported by a tie rod CF and a pin support at A. The diameter of the tie rod CF is 30 mm, and the cross-sectional area of member BD is 900 mm?. The diameters of the pins at A and D are 8 mm and 12 mm, respectively, and each pin is subjected to double shear. If the weight of the bucket hanging from end E is 3 kN, determine (a) The axial stresses in tie rod CF and member BD. (b) The shear stresses in pins A and D. - 0.6 m-0.6 m→ D E 0.6 m V30B 1.2 m F
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
Given: Four-25-mm-diameter rivets with an axial load of T = 75 kN distributed equally as shown. The thickness of the plates is 25 mm and the width of the plate is 150 mm. find (a) the shear stress on the rivets (b) the bearing stress between a plate and a rivet; (c) the minimum average tensile stress in each plate. Show detailed solution and draw FBD.
A double tee cross section is used for the beam shown below. Assume the following lengths and loads: a = 15 ft b = 8 ft C= 10 ft P= 12500 Ib Q= 5000 lb The moment of inertia of the cross section is i, = 110 in.". Determine the magnitude (ie, the absolute value) of the maximum compressive bending stress in the beam. TT 3.2 in. B D 5,8 in. Answer: Omax (Compression) = 1 psi %3D
A compound shaft made of steel and aluminium transmits 75 kW at 900 rpm. Determine the maximum shear stress and relative angle of twist between surfaces at two extreme ends located at A and C. Neglect any strain concentration effect. Esteel = 207 GPa, EA1 = 73 GPa, VAI = 0.334, and Vsteel = 0.33. F Aluminium 60 800- B Steel 75 1000 All dimensions are in mm
PROVIDE A CLEAR SOLUTION AND THE RIGHT ANSWER FOR THIS PROBLEM. PROVIDE INDIVIDUAL FBD
1) will upvote anyone who will answer
Two forces, each of magnitude P, are applied to the wrench. The diameter of the steel shaft AB is 15.3 mm. Determine the largest allowable value of P (in N) if the shear stress in the shaft is not to exceed 87.95 MPa and its angle of twist is limited to 5.41°. Use G = 80.32 GPa for steel and L= 433 mm. Round off the final answer to two decimal places. ... P -300 mm P- B L A

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS