- The following data were obtained from a test on a pelton wheel : (i) Head of the base of nozzle = 32 m (ii) Discharge of the nozzle = 0.18 m³/s (iii) Area of the jet= 7500 sq mm (iv) Power available at the shaft = 44 kW (v) Mechanical efficiency = 94% Calculate the power lost (1) in the nozzle. (2) in the runner and (3) in moch

- The following data were obtained from a test on a pelton wheel : (i) Head of the base of nozzle = 32 m (ii) Discharge of the nozzle = 0.18 m³/s (iii) Area of the jet= 7500 sq mm (iv) Power available at the shaft = 44 kW (v) Mechanical efficiency = 94% Calculate the power lost (1) in the nozzle. (2) in the runner and (3) in moch

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Oil with sp. gr. of 0.87 is being pumped from a lower reservoir to an elevated tank as shown. The pump in the system is 78% efficient and is rated 185 kW. Determine the energy added by the pump. 160mm w EL. 200m 200mm 9 El.150m Oif. Sp.gr.=(0.82
(b) A water turbine model is constructed at ratio of 1:8 with power system of 10 kW at speed of 555 rpm under a head of 2.5 m. Overall efficiency for both model and prototype is assumed at 0.93. (i) Detemine the specifie speed. mine t); (ii) If the prototype is run under a head of 25 m, calculate its rotational speed, power and discharge.
Correct solution.
Plz write neat
The pump draws oil with specific gravity of 0.90 from a reservoir and delivers it to the hydraulic cylinder. The cylinder has an inside diameter of 5.0 inch and in 15 seconds the piston must travel 20 inches while exerting a force of 11,000 lb. It is estimated that there are energy losses of 11.5 lb-ft/lb in the suction pipe and 35.0 lb-ft/lb in the discharge pipe. Both pipes are 3/8-in Scheulde 80 steel pipe with inside diameter of 0.423 inch. Calculate the pressure at the cylinder.
A steam turbine is to operate on a simple regenerative cycle. Steam is supplied dry saturated at 40 bar, and is exhausted to a condenser at 0.07 bar. The condensate is pumped to a pressure of 3.5 bar at which it is mixed with bleed steam from the turbine at 3.5 bar. The resulting water which is at saturation temperature is then pumped to the boiler. For the ideal cycle sketch the process on the T-s diagram and calculate, neglecting feed pump work,The amount of bleed steam required per kg of supply steamThe thermal efficiency of the plantThe specific steam consumption
Consider a pump–turbine that operates both as a pump and as a turbine. Under conditions in which the rotational speed ? and the volume flow rate V. are the same for the pump and the turbine, verify that turbine specific speed and pump specific speed are related as
A nozzle discharges water at a velocity of 20 m/s. If the head loss through the nozzle is 6 m, then the coefficient of velocity of this nozzle will be (a) 0.98 (b) 0.95 (c) 0.90 (d) 0.88
ion 10 A 1-meter diameter new cast iron pipe 845 m long and has a head loss of 1.11 m. Find the discharge capacity using Darcy Weisback formula with f = 0.021. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: liters/s Decimal Places required in the final answer: 3
Q3) In impact of jet experiment if the supplied discharge Q through a 5 mm diameter nozzle is (0.25 L/s), find the required weight W that is needed to support the plate in its initial position as shown in figure. 50 mm W Nozzle
PLEASE PROVIDE A COMPLETE SOLUTION WITH FIGURE FOR ME TO FOLLOW :) ANSWER IS GIVEN FOR REFERENCE. THANK YOU!