The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Fy Horizontal Thrust block F, 30° 50° (2 Open end Ø 80 mm Ø 160 mm Figure 3 Vertical

The flow rate of water flowing out of an 80mm diameter nozzle shown in Figure 1 is 60 litre/s. The volume of the water in the pipe bend is 50 litres and the pipe bend is installed in a vertical plane. The head loss from point 1 to 2 is 0.44m. Calculate the x and y for components of the thrust block to hold the pipe bend. Fy Horizontal Thrust block F, 30° 50° (2 Open end Ø 80 mm Ø 160 mm Figure 3 Vertical

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

please solve it fast l will put like
A differential manometer is attached to a pipe as shown. Calculate the pressure difference between points A and B
4
P₁ = 80 kPa B 3 m PB = 50 kPa Calculate the friction head loss for a water Q-1 flowing from point A to B.
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
Water is pumped at a rate of 21.4 m/s from tank (A) and out through a 300.5 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70 m, Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the ViScosity), Usef 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation 135 Elevation 140 m Tank (B) Tievation 100m Tank LA) Jund: Elevitions in Write the answer for any numbers after the declmal
= constant Q16/ A pipe diameter of 400 mm carries water at a velocity of 25 m/s. The pressures at the points A and B are given as 29.43 N/cm² and 22.563 N/cm² respectively while the datum head at A and B are 28 m and 30 m. Find the loss of head between A and B. Z شكر الكائر 2B ADA=400 mm PA 29.43 N/cm #28 m ZA 28 Dg= 400 mm Pe = 22.563 N/cm ZB = 30 m DATUM LINE
A turbine with a power coefficient Cp = 0.28 is able to generate 2.1 MW of electrical power with blades of length R =75 m. What is the value of the wind speed? Calculate the value in meters/second and round off to two decimal places. Do not write the unit.
Please don't copy the answer from the online pdf. I need explanation+diagram
Solve it correctly please. I will rate accordingly with 4votes.
Hi. Kindly assist with this Fluid Mechanics question.Please answer correctly and show all the steps
+7