The floor joists in a residential house are made from seasoned MGP timber. Knowing the house is located in the northernmost part of Darwin, which has a very high average humidity. There are five floor joists sharing the load (spaced at 1.5m center to center). MGP15 240x45 Timber L (m) = 7.1 Dead Load = 6 Live Load = 2 1. Determine if the section satisfies serviceability limit state design 2. Check whether or not the section sustains the critical bending moment. Knowing that the floor joist bends about the x-axis.

The floor joists in a residential house are made from seasoned MGP timber. Knowing the house is located in the northernmost part of Darwin, which has a very high average humidity. There are five floor joists sharing the load (spaced at 1.5m center to center). MGP15 240x45 Timber L (m) = 7.1 Dead Load = 6 Live Load = 2 1. Determine if the section satisfies serviceability limit state design 2. Check whether or not the section sustains the critical bending moment. Knowing that the floor joist bends about the x-axis.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ELerED HAFTERG 24 20 BEAFING WALL RAFTERG@2fao. -BEAM COLIMN FRAMING PLAN A BEAM -COLUMNS BEABING WALL FRONT ELEVATION SIDE ELEVATION • Live snow load = 25 psf • Dead load: (1) Roof and Sheathing 14 psf, (2) Rafters = 4 lb/ft • Roof pitch: 5:12 Please round to the nearest one tenth (i.e., 0.1). Total load (LL + DL) on a middle rafter after adjusting to horizontal projection = Ib/ft MacBook Air 80 F3 D00 F4 F2 F5 F6 F7 # % & 2 3 5 6 %2 4
Question 5 (2 points) v Saved The CLT members are used as columns True False Question 6 (2 points) v Saved The vertical member in the wood framing within the load bearing walls is called Joist Stud Bridging Rafter Question 7 (2 points) v Saved Wood members should be raised from the ground True False
Three Strength Class C16 sawn timber joists are bolted together to create a trimmer beam which supports the first floor of a new house. The top flange of the trimmer joist is laterally restrained. The floor load is the usual dead and imposed in a domestic property. What is the design moment resistance of one of this group of joists? Joist width-60 mm Joist height-212 mm Give your answer to one decimal place in kNm.
#2 will upvote anyone who will answer correctly. Thanks
Solution?
2. Roof joists are spaced at 2m and span 6m between supporting girders, and joist depth of 600mm. The allowable deflection limits for OWSJ are L/360 under snow load. The OWSJS are subjected to a dead load of 2.96kPa which includes the estimate joist weight of 0.15kPa, an occupancy load of 2.4kPa, and the following: SULS 1.99kPa SSLS = 1.25kPa Select a suitable OWSJ which satisfies the limit states design.
A 4”x8” wood was tested for its compressive strength parallel to the grain. The max load at failure is 12,000kgf. Determine the compressive strength in MPA.
2.14 The number of accidents at rail-highway grade-crossings reported for a province over the last 10 years are summarized and classified as follows: Type of Accident (R) Run into Train (S) Struck by Train Day (D) Night (N) Time of 30 60 Occurrence 20 20 Suppose there are 1000 rail-highway grade-crossings in province XY. (a) What is the probability that an accident will occur at a given crossing next year? (Ans. 0.013)
What is the reference shear stress for Alaska Yellow Cedar No. 3 dimension lumber?Fv=_______ psi
Softwood advantages and disadvantages.