The flanges used in the connection of the two shafts are connected to each other with 6 bolts. The shaft diameter is 100mm and transmits a torque of 300Nm. The diameter of the circle passing through the bolt connections is 200mm. Since the diameter of the bolt is 10mm and the permissible shear stress is 40MPa, is the number of bolts sufficient?

Q: Attention !!!! Please clarify this . When they go to calculate both the normal stress of the bolt…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine stress in rod

A: Given data :   Length (L)=5 mArea (A)=100 mm2Force (F)=10 KN

Q: The five-bolt connection must support an applied load of P = 4400 lb. If the average shear stress in…

A:

Q: Two steel springs arranged in series supports a load P. The upper spring has 12 turns of…

A:

Q: -01 Por the assembly ahovn the allovable atreas in the 75-mm diameter rod BC is 80 MPa, and 50 MPa…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: Unit of stress and unit of shear modules is the same.   Select one: True False

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: - 62.5 mm - Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm…

A:

Q: Please solve this question in detail. You have to add the free body diagram.

A:

Q: M2

A: Sign convention for shear force for the left side of the section: Upward force - Positive Downward…

Q: What is the vertical displacement at joint F. Assume all members are pin connected at their end…

A:

Q: 2- What is the maximum shear stress in the shaft in (MPa)?

A:

Q: find the required wall thickness of the cylinder.

A: find the required wall thickness of the cylinder.

Q: find the bearing stress between bolts and plate 10/-.. 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN…

A: Given data  diameter of bolt (d) = 10 mm thickness of plate (t) = 8 mm  Load acting on the plate…

Q: BP1: A wire hook is loaded with F=2000 lb. The hook has a wire diameter of 1", eye diameter of 3",…

A:

Q: (D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: Find the internal forces as a function of θ.

A: As the load acting in downward direction take the sign convention of the downward force as negative…

Q: For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the…

A:

Q: A solid aluminum 2014-T6 shaft with a diameter of 80 mm is inserted concentrically inside a steel…

A:

Q: A mild steel shaft transmits 18 kW at 450 r.p.m. It carries a central load of 900 N and is simply…

A: Maximum tensile or compressive stress=56 MPa

Q: Determme the snallest allowable diameter of the solded shuft ABCD, knowng that the allowable shear…

A: Given data as per question Allowable shear stress = 60 Mpa The radius of disc B =80 mm…

Q: 1.5m 1.5m x A C. B 2m/2 D (0.0.3) ( / B (5, 0, 3) FAB Z W C (-5, 0, 3) FAC A (0.2.1.5) C 5m E(0. 4.…

A:

Q: An L-shaped bracket is supported by a frictionless pin at A and a cable between points B and D. If…

A:

Q: A solid 4340 HR Steel tie rod of length Lrod = 950 mm is employed to compress à 6061-T6 aluminum…

A: 4340 HR steel rod.Diameter of the rod, drod= 27.5 mmLength of the rod, Lrod= 950 mm6061-T6…

Q: The solid rod with radius r=34 mm is subjected to the loading F1=120 kN, F2=44 kN, F3=17 kN. With…

A:

Q: The solid rod AB has a diameter dAB5 60 mm and is made of a steel for which the allowable shearing…

A: Given Data: The diameter of the rod AB is: dAB= 60 mm The outer diameter of the pipe CD is: dCD=90…

Q: A cast ALuminum cy linder o f Purtable hydraulic a riveter is 208 mm in diameter The Pressure 16,8…

A: The above questioni is based on cylinder analysis.

Q: 62.5 mm Key 550 The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists…

A:

Q: A pressure of 40 MPa shall be contained in a pressure vessel with inner diameter 0.30 m. Find the…

A: Given: Pressure, P = 40 Mpa Inner diameter, d = 0.3 m Maximum tensile stress, σu = 646 Mpa Factor of…

Q: The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the…

A:

Q: The driveshaft of an automobile is being designed to transmit 131 hp at 2960 rpm. Determine the…

A: To Find : The minimum diameter required for the solid steel shaft. Given : The allowable shear…

Q: If the chaft shown in Figure is made of one material and is subjected to torques TI-25 kN.n and…

A:

Q: Need in 1hour pls, thanks The technician is exerting a force of 200N to adjust the shaft at A as…

A:

Q: Determine the reaction loads and maximum shear stress ! 200 Ibf-in z-in dia. A B 4 in 6 in

A:

Q: The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm…

A: According to the given data F=6 N We need to find Force on the fingernail by the cutter

Q: The five-bolt connection must support an applied load of P = 4300 lb. If the average shear stress in…

A:

Q: The A30 sloel bolf is tightened within a hole so that the eactive torque on the shank AB can be…

A: Given DataT=50N.mt=kx2/3G=75GPa

Q: In which option the place and value of the maximum stress that will occur in the ABCD stepped shaft…

A: Given data: TA = 45Nm TB= 15Nm TD = 20Nm d1= 20mm d2= d3 =24mm Need to determine the place and value…

Q: The five-bolt connection shown must support an applied load of P-500 kN. If the average shear stress…

A:

Q: Q3/ Two plates are riveted together have a width of 130 mm, thickness of 25 mm and the diameter of…

A:

Q: Following plate is connected to the wall using 7 bolts. Cross sectional area of each bolt is A.…

A: Given- Force F is passing through the center of gravity of the plate, so it will be equally…

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A: