The concrete pipes culvert (n = 0.012) must carry the flow from open channel half square section 4m wide and 2m deep (n = 0.015 and S = 0.001) the depth of water is 1.5m. Determine the diameter of pipe the length of culvert is 30m K, = 0.5, tailwater31.3m and max headwater is %3D 4.8m.

The concrete pipes culvert (n = 0.012) must carry the flow from open channel half square section 4m wide and 2m deep (n = 0.015 and S = 0.001) the depth of water is 1.5m. Determine the diameter of pipe the length of culvert is 30m K, = 0.5, tailwater31.3m and max headwater is %3D 4.8m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Q1: A box culvert of (3×3)ft designed to accommodate 135 ft³/sec. the culvert length and slope are…

A: Given, Q = 135 cfs L = 100 ft S = 2.5% TW = 5 ft

Q: A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and…

Q: A hydraulic jump o<<urs in a horizontal rectangular <hannel, which is I m wide. The pre-jump depth…

Q: 1 m A Soil B 1 m 0.8 m Datum Table Figure Q2 (b) (i) Total head at A and B (ii) Hydraulic gradient.…

A: V=2.5 cm3 t=5 sec l=1m

Q: The ratio between the discharge and top width of a best hydraulic rectangular channel is (91/50) ,…

A: Given,The ratio between the discharge and the top width, QT = 9150Bed slope, S = 13000 and C = 50For…

Q: Q1:- Determine the cross section and discharge of the stable hydraulic section of a channel…

Q: 1. Water flows in symmetrical trapezoidal channel lined with asphalt has a base width of 4.8 m and…

A: Data givenBase width, B = 4.8 mSide slope = 3 H : 1 Vn = 0.015Channel drop= 0.1 m to every 100 mFind…

Q: Design a concrete lined channel of trapezoidal section to carry a discharge of 250 cumecs at a…

Q: ta triple concrete box culvert 1.5 m by 3.7 m (n=0.012) conveying a discharge of 46m3/s operates…

A: Culvert dimensions: 1.5 m x 3.7 m n = 0.012 Discharge, Q = 46 m3/s Length, L = 32 m Slope = 0.75%…

Q: . If discharge = 0.80 m^/sec, determine the slope of the rectangular plane timber flume. 2. What…

Q: A hydraulically efficient trapezoidal channel section has a uniform flow depth of 2 m. The bed width…

A: Given data in question Hydraulically efficient channel Trapezoidal channel Uniform flow depth To…

Q: 500 mm diameter pipe is laid on a slope of 0.002 and is to carry 40 liters/sec. Using n = 0.013,…

Q: A circular section channel 3 m in diameter has a depth of 1.0 m and is laid to a gradient of 1:1000…

Q: A box culvert of (3x3)ft designed to accommodate 135 ft3/sec. the culvert length and slope are 100…

Q: A concrete lined channel is to be constructed. For concrete in this case take Manning’s n to be…

A: Calculation of value DQ=AR2/3S1/2η8.5=1.732D2×(0.500D)2/3(1450)1/20.014D=1.369m

Q: Determine the Hydraulic radius if area oc channel is 20 m2 and wetted perimeter is 14 m

A: Given Area 20m^2 Wetted perimeter 14m Hydraulic radius ?

Q: 4. Water circulates through a circular channel with a diameter of 1.6 m with a depth of 1 m. The…

Q: Q 2. Design a lined canal cross section to carry a discharge of 3 cumecs on a slope of 25 cm/km. The…

A: Consider the maximum permissible velocity as 0.8 m/sec. Discharge Q = 3 cumecs Slope n = 25 cm/km =…

Q: A steel rectangular channel is to carry flow rate of 1.90 m3/s with a slope of 0.01 and roughness…

Q: A rectangular channel (b = 9 feet) crosses beneath a roadway inside a 70-inch RCP culvert with a C =…

A: Width of rectangular channel, Diameter of Culvert, Design Flow rate, Standard Length of 70-in RCP…

Q: Triangular or “V” shaped channel with the sides inclined at an angle, θ = 60O from the horizontal…

A: Objective: To determine the hydraulic radius of the triangular channel. Given: Depth of water in…

Q: Open channel flow

A: Given data : Depth of flow (d)=2.5 mwide (B)=5 m

Q: How much is stress at point.... in the following culvert considering applied moment of 100…

A: Given data, M = 100 kips-inch.

Q: A triangular section has a side slope of s = 2, Manning's n = 0.02, Bottom slope of S0 = 0.005,…

A: (1) It is required to determine the top width of the triangular channel. T=2sy=2×2×2=8 m It is…

Q: A box culvert, as shown in the figure, was designed to carry a discharge (Q m'is) from a square…

Q: Ex 3 :Hw 2 Design unlined canal to carry a discharge of 1.0 m3 /s with a longitudinal slope 20cm/km…

A: Question is based on design of canal using lace's theory. Design discharge, slope, manning constant…

Q: b) Design a box culvert for the given data: Q = 43.8 m³/sec; length of culvert (L) = 50 m; Ke = 0.3;…

Q: 4. The hydraulic radius of a triangular section is 0.45m and the normal depth of the channel is 2m,…

Q: Determine the discharge through a right angled triangular section for a normal depth of 3.7 ft;…

Q: A concrete lined channel is to be constructed. For concrete in this case take Manning’s n to be…

A: Given Discherge Q=8.5 m3/secmanning co efficient n=0.014 side slope S=1450velocity by…

Q: Exercise [3] Calculate the depth d in which the discharge (Q=1.5 m³/sec) will flow through the…

Q: Required: wetted perimeter of the canal, x-sectional area and hydraulic radius

A: Given:- Width, b = 2 ft Flow depth, d = 3 ft Total depth, D = 3.1 ft Side slope = 4:1 To find:-…

Q: Design a concrete-lined canal cross section to carry a discharge of 24 cumees. The longitudinal…

A: The canal is an artificial outlet constructed to overcome the shortage of water for daily use and…

Q: A dam spillway is to be designed as a combination of a circle-quadrant and rectangular cross-…

A: Introduction : At the top of the reservoir pool is a spillway. Bottom outlets with valves or gates…

Concept explainers

Highway Drainage

Highway drainage is the process of extracting and regulating the excess surface water on the pavement by giving the desired slope. The construction of a highway drain helps to divert the water present on the surface, and sub-grade by the means of slope. Highway drainage systems are a necessary part of smooth functioning of traffic, since the highway drainage systems provide proper disposal of unwanted substances from the highways.

Question

H.W2/ The concrete pipes culvert (n = 0.012) must carry the flow from open
channel half square section 4m wide and 2m deep (n 0.015 and S =
0.001) the depth of water is 1.5m. Determine the diameter of pipe the
length of culvert is 30m Ke = 0.5, tailwater=1.3m and max headwater is
%3D
4.8m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

Step 2 Formula Used

Step 3 Calculations

Step 4 Calculations

Step 5 Answer

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the best hydraulic section for rectangular channel that can carry 200 m^3/min.
bottom width of trapezoid-shaped canal = 1.5 meters depth of flow = 1.5 meters side slopes = 3H : 2V channel slope = 3 meters/5000 meters n = 0.013 What is the discharge in this canal lined with concrete?
*hydraulics *use handwritten A rectangular channel 5.50 m wide and 1.30 m deep is laid on a uniform slope of 0.002. The roughness coefficient of the channel is 0.013. Which of the following most nearly gives the saving’s in lining per meter length of channel that could have been offered by using the most efficient rectangular section but adhering to the same flow capacity and slope in m^2/s. Choices are A.) 21.04 B.) 13.02 C.) 1.03 D.) 22.63 E.) 0.24 F.)0.67 note: the unit should be in m^2/s.
PLEASE SOLVE PARTS (E) AND (F)
Calculate the depth d in which the discharge (Q=1.5 m³/sec) will flow through the channel with trapezoid-shaped cross section. Width of the channel bed is (b =2 m), slope of bed (S=0.05%), sides slope is (Z=1.5). The channel is excavated in gravel sends in which the roughness coefficient is (n =0.0247).
Subject : Fluid mechanics Please read the question carefully and give me right solution according to the question. Thank you
The water cross-sectional area of a culvert is 18.36 sq.m. and wetted perimeter is 12.56m. If the flow is 45.68 cu.m. per s and n=0.015, find the slope.
Fluid mechanics
2. Designing an open channel_to convey the water to the two downstream communities where, the level of the two downstream communities relative to the dam bed is shown. 2.1 Design an open channel using Manning equation. The channel should carry a flow rate of 8.5 m/s. Use the best hydraulic section approach to size the channel. It is concrete lined with a bed slope of 0.001m/m, and a side slope of 2. 2.2 Show a section of your designed channel with specified dimensions (use a proper drawing to scale).
4- Design a concrete (n=0.012) trapezoidal channel carrying a discharge of 5 m³/s with a longitudinal slope of 0.0015 based on the following conditions. (a) Most hydraulically efficient cross section. (b) Use the side slope of 2H:1V. (c) Calculate the critical depths for both cases. Note: Use a freeboard of 0.5 n m.
Question 4 A nearly horizontal rectangular section with a width of 25 feet carries 1500 cfs. There is a contraction in the channel of 10 feet. If the depth at the contraction is critical determine the upstream channel depth in feet. Do not include the units in the solution and round to the tenths digit. D Question 5 Assume you have the channel reach shown that is mild (dn>dc); calculate the upstream and downstream depths of the hydraulic jump (note there is a hydraulic jump because upstream there is a gate controlling the water to below critical. Also determine the length of the hydraulic jump. The flow rate in the channel is 1500 cfs, , the base width is 25 ft and the normal depth is 10 feet. upstream depth - ft downstream depth = ft length of jump = ft Round all you answers to the hundredths digit and do not include units in the solutions and on your scratch paper provide a sketch of the channel in profile view. please answer both, will upvote
Determine the normal and critical tie rods in a trapezoidal channel with a stencil width b = 3m, slope k = 1 and bottom slope S = 0.002. The Manning's roughness coefficient is n = 0.035 when conveys a flow Q = 15 m3/s. Also calculate the Froude number to determine the flow regime.