The beam shown carries a concentrated load P = 500 N and a concentrated moment M = 200 N-m. Dimensions a, b, and c are 2 m, 3 m, and 4 m respectively. Determine the bending moment, in N-m, in the beam at the concentrated moment. M a. -200 c. -680 b. -550 d. -1080

Q: Find Wi andwe m2

A: Given data: -  The total length of string 1 is l1. The total length of the string 2 is l2. The…

Q: bäi The command using to insert :seal is

A: The Incident Command System is a standardized approach to the command, control, and coordination…

Q: For the 90° V6 engine operating on a 4-stroke cycle with firing order 1-4-5-2-3-6 (see sketch),…

A: Solution: 1) Primary and secondary shaking forces- Inertia force due to reciprocating parts of…

Q: 2. A four-stroke reciprocating engine have a 2000 indicated horsepower. What would be the indicated…

A:

Q: Which of the following tools is used in both marking and measuring? O Center Punch O Mallet O None…

A: Center punch is a marking tool used to mark center of a hole which is to be drilled. It is not a…

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: where are the graphs?

A: Given data in the related question: Maximum speed = vf = 183.58 mi/hr Distance travelled = 5 mi Time…

Q: b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 28 mm and…

A: Given data: In a four-cylinder four-stroke internal combustion engine Bore diameter d=28 mm=0.028 m…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: The gas turbine cycle consists of four thermodynamic processes as follows: 1-2: Work output from…

Q: 04: Complete the secetion of the reciprocating pump (shown in figure.2) by adding the details of the…

A: Gear box in the reciprocating pump The purpose of the gearbox is to convent rotating energy to…

Q: Respond with TRUE if the symbol of the valve shown below is drawn corectly 2 3 IMM 4 15

A: Directional control valves: The valves which is used to allow fluid flow into different directions…

Q: (a) tang tan

A: Given data: Opposite side =4 Adjacent side=2

Q: Mercury has a uniform coefficient of expansion Select one: O True O False

A:

Q: Determine, using the principle of superposition, the reactions at supports A and B for equilibrium.…

A:

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 289 K and…

A:

Q: What happen when input II (push button) is pressed. 11 Q1 () Q1 Q2 O a. Ql -1 Q2 0 Ob.Ql-1Q2 1 Oc.…

A: The correct answer for the above mentioned question is given below. I am pretty sure of the answer.

Q: QUESTION 3 Code for a clockwise circular move to an end point that is 1 inch over in the X direction…

A: consider the following diagram:

Q: Iron Ore are mainly used to produce high heat in blast furnace

A: I think its answer should be False. Because blast furnace is used to melt iron ore by reducing…

Q: State four espect to consider before selecting correct solvant

A:

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: In a gas turbine, the temperature of the working fluid at inlet to the compressor is 286 K and…

A: This problem is based on Bratton cycle and can be solved as :

Q: Sing do Coso + Cose-2

A: Find the integral of the given function.

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: idk where you got the 4 from

A: The number of independent equations=5The number of unknowns=7To determine:Degree of freedom

Q: 21:00 O O O 令. 63%i Details What is the value of the current 1? 5A 2A ЗА a. 12A O b. 10A Oc. 11A

A:

Q: what is the omega value? as per the professor, the IC is at b not a

A: Given: The velocity of the upper wire: →V=5.6 m/s It is right that the instantaneous center of…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given -  L = 25 ft = 25 × 12 P = 10000 lb  ∆L = 0.477 in  E = 30 × 106  psi

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: Q2 (a) Figure Q2 (a) shows two vectors FA and Fa represent the forces exerted on the pulley by the…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: DRAW THE MULTIPLE VIEW

A: The given view is in isometric view

Q: The Compressors have a diffusers to increase the pressure energy Select one: True O False

A: Concept: 1) A compressor is a mechanical device which is used to increase the pressure of gas .  2)…

Q: step of construction with sutible dimmenstion

A: To show the step of construction with sutible dimmenstion

Q: 1. What is the name of the circuit? 2. How many reservoir symbols are shown, and how many reservoirs…

A: As per Bartleby Answering Guidelines we are supposed to give answer first three sub parts of the…

Q: 27. A cylinder is required to move a 4200 lb load 20 inches in 2 sec- onds. What is the output…

A: Given : force = 4200 lb distance = 20 inches time = 2 sec   velocity = distance/time  = (20/2) = 10…

Q: the p-value 42,45,38,37.5 ,41 40.5,45,36,37.5,39

A:

Q: 1a) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 43 mm and…

A:

Q: Do number 13.12

A: Given Data Qr=24000 BTU/hr EER=11 Cost= 14 cents per kWh

Q: Match the given functions with the components of a wind turbine. Connects the rotor hub to the gear…

A: a) Main Shaft connects the rotor hub to the gearbox.