Tem 9.8 A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressure p, while the ends are subjected to an external pressure of 1/2 p. Determine the value of p at which elastic failure will occur according to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit of proportionality of the material in simple tension is 270 MN/m². What will be the volumetric strain at this pressure? E = 210 GN/m²; v = 0.3. svede ba

Tem 9.8 A thin cylinder of 300 mm internal diameter and 12 mm thickness is subjected to an internal pressure p, while the ends are subjected to an external pressure of 1/2 p. Determine the value of p at which elastic failure will occur according to (a) the maximum shear stress theory, and (b) the maximum shear strain energy theory, if the limit of proportionality of the material in simple tension is 270 MN/m². What will be the volumetric strain at this pressure? E = 210 GN/m²; v = 0.3. svede ba

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In constructing a large mobile, Jude hangs an aluminum sphere of mass 6.0kg from a vertical steel wire 0.50m long and 2.5x10^−3 cm^2 in cross-sectional area. On the bottom of the sphere, he attaches a similar steel wire, from which he hangs a brass cube of mass 10.0kg. For each wire, compute: (a) The tensile strain and(b) The elongation
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
C A cantilever beam is subjected to a downward force of 5 kN at its free end, as shown in Fig. 1. The beam is supported by a circular bracket (BD) attached to a wall. The bracket is made of ductile steel whose elastic limit is 300 MPa, both in tension and compression. Determine the diameter of supporting post using Von-Mises theory. (Hint: Neglected the weight of the beam, the ends B and D are welded) Fig.3 3 m B 2 m 2 m 2 m 5 kN
For a given homogeneous, isotropic, linearly elastic material, E = 15e6 psi and v = 0.3. Solve for the shear modulus. 2.1.1 Homogeneous, isotropic, linearly elastic materials For specimens undergoing small deformations, the stress-strain diagram often ex- hibits a linear behavior. Although this is a very crude approximation to the behavior of actual materials, it is a convenient assumption that is often used for preliminary evaluation. A linear relationship between stress and strain can be expressed as 01 = E €1, (2.1) where the coefficient of proportionality, E, is called Young's modulus or modulus of elasticity. Since strains are non-dimensional quantities, this coefficient has the same units as stress quantities, i.e., Pa. This linear relationship is known as Hooke's law. The elongation of a bar in the direction of the applied stress is accompanied by a lateral contraction that is also proportional to the applied stress. The resulting defor- mations for this uniaxial state of stress…
None
i li. الامتحان هو سؤالان فقط Q. 1: If a material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength - 900 Mpa) and the stress state at a point is shown in Fig. 1. Using a graphical method, find safety factor against static failure using 100 Mpa (a) Rankine failure theory (b) Coloumb - Mohr theory (c) Modified Coloumb - Mohr theory 50 Мра إضافة ملف Q.2 For a rotating shaft of diameter 15 mm as shown in Fig. 2. If the material is AISI-1045 CD, Find the safety factor II >
need correct ans
a rectangular stepped bar is shown. the bar is loaded in bending. determine the fatigue stress concentration factor if the ultimate stress of the material is 690 mPa. please inlcude how to calculate the notch sensitivity.
A bar of 6-mm in diameter is only allowed to decrease at a maximum of 3.96% of its total length. What is the maximum force (Newtons) that can be applied? Consider the shear modulus = 602 MPa, and the Poisson's ratio as 0.20. Express your answer in three decimal places.
A sheet metal cutting machine cuts the sheet metal via shear force, V as shown in Fig. 1. The crosssection of sheet metal is rectangular with width, b = 3m and thickness, d = 5mm. The sheet metal ishaving yield strength σy = 220 MPa; Young’s modules, E = 200 GPa and Poisson’s ratio, ν = 0.3.Conduct the following analyses at the state of stress when maximum stress reaches σy and beforeshearing commences. (Need answer Question c) & d) c. Sketch the YIELD LOCI for both cases above. d. As a sheet-metal engineer, which failure criterion in (b) will you use to determine the cuttingshear force? Explain the reason for your answer.
1) The triangular plane stress problem connected to a spring, is subjected to a uniformly distributed load and two point forces. Calculate the nodal displacements and the spring force using two triangular finite elements. k = 3x105 kN/m (spring constant) h = 0.20 m (thickness) E = 3x107 kN/m² (modulus of elasticity) v = 0.20 (Poisson's ratio) 1.5 m 40 kN 30 kN/m 50 kN 2 m 2 m
Please provide the correct solution asap. Handwritten recommended