*(t) = Ax(t) + Bu(t) = [% Jx(+) + [7] u(t) y(t) = Cx(t) = [g_h]x(t) %3D A control system is described by the fllowing state and output equations. Assuming a=34, b=10, c=10, d=6, e=0, f=1, g=1, and h=0. Find the transfer function (TF) of the system in the form: a¡s + ao TF(s) = b3s3 + b2s² + b,s + bo , What is the order of this system (SOj? Finally, fill in the following blanks by the values of aj, bi, and the system order (SO). Notes: 1) Based on the order of the system (SO), the coefficient of the higher part of the characteristie equation (denominator) should be 1 (Ex for So = 3: s° + 2s² + 5s +3, 2) You should fill the blanks with numbers only and with one decimal at max as EX: 12.1 3) The error is not cumulative and if you don't know any answer, just fill it with any random number more than I (zero is not acceptable). Ex for SO = 2: s² + 3s +4 ) 1) The value of a, = 2) The value of ao =

*(t) = Ax(t) + Bu(t) = [% Jx(+) + [7] u(t) y(t) = Cx(t) = [g_h]x(t) %3D A control system is described by the fllowing state and output equations. Assuming a=34, b=10, c=10, d=6, e=0, f=1, g=1, and h=0. Find the transfer function (TF) of the system in the form: a¡s + ao TF(s) = b3s3 + b2s² + b,s + bo , What is the order of this system (SOj? Finally, fill in the following blanks by the values of aj, bi, and the system order (SO). Notes: 1) Based on the order of the system (SO), the coefficient of the higher part of the characteristie equation (denominator) should be 1 (Ex for So = 3: s° + 2s² + 5s +3, 2) You should fill the blanks with numbers only and with one decimal at max as EX: 12.1 3) The error is not cumulative and if you don't know any answer, just fill it with any random number more than I (zero is not acceptable). Ex for SO = 2: s² + 3s +4 ) 1) The value of a, = 2) The value of ao =

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer in 30 minute
I am posting this for third time please don't copy previous solution as they are wrong and give detail explanation.
How does TP4056 works? What is the purpose of red and blue lights in the components?
Assume that a 10kW air conditioner would run 75% of the time during the peak hour and might be limited by utility remote control to a duty cycle 0f 60%.Determine the following (a) The number of minutes of operation denied at the end of 1 hr of control of the unit. (b) The amount of reduced energy consumption during the peak hour if such control is applied simultaneously to 100,000 air conditioners throughout the system. (c) The total amount of reduced energy consumption during the peak. (d) The total amount of additional reduction in energy consumption in part (c) if T&D losses at peak are 8%.
How can IoT be used to improve energy efficiency in smart homes and buildings?
What function does a classic load balancer serve? I need like three sentences.
5 Which button is used to run the simulation in LTspice program?
Explain the importance of power system stability in electrical engineering.
What are the limitations of Microstrip Transmission Line PCB?
What is meant by FACTS in power systems? Discuss about UPFC type FACTS device.
What is reverse engineering and how does it work?
1. Explain the concept of "EXTENDED EQUAL AREA CRITERION"