Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed through a heat exchanger where it is heated until it reaches saturated liquid-vapour state at a quality of 0.53. If the water absorbs 342 kW of heat from the heat exchanger to reach this state, calculate how many kilogrammes of water flow through the pipe in an hour. Give your answer to one decimal place.

Subcooled water at 5°C is pressurised to 350 kPa with no increase in temperature, and then passed through a heat exchanger where it is heated until it reaches saturated liquid-vapour state at a quality of 0.53. If the water absorbs 342 kW of heat from the heat exchanger to reach this state, calculate how many kilogrammes of water flow through the pipe in an hour. Give your answer to one decimal place.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is stored in a closed tank of capacity 0.1m3. The quality of water is 60% and initial pressure is 7 bar. Heat is transferred to the water until the tank contains only saturated vapour. At the end of this process, determine the mass of vapour in the tank, and the final pressure inside the tank.
In a turbine 1,308 kW is produced by expanding an exhaust gas entering at 2.2 MPa and 662 K to a final pressure of 154 kPa. The inlet area of the turbine is The inlet area of the device is 0.2 m2 and the gas velocity at inlet is 25 m/s and at outlet is 51 m/s. Determine the specific volume at outlet in m3/kg to 2 decimal places. Assume the gas constant to be 0.26 (kPa m3)/(kg K) and constant specific heats cp=1.01 kJ/(kg K) and cv=0.75 kJ/(kg K).
A 110-volt 6 Ampere electric heatrer is submerged in 1 kg of water for 24 minutes. What will be the final temperature of the water if its initial temperature is 23 C. Assume a heat loss of 13%.
Please state the assumptions and tables.
Refrigerant 134a expands in a piston-cylinder assembly from p₁= 200 lb/in² and T₁ = 140°F to p₂ = 30 lb/in² and T₂ = 80 °F. The mass of refrigerant is 0.46 lb. During the process, the work done by the refrigerant is 4.32 Btu. Kinetic and potential energy effects are negligible. Determine the initial volume of the refrigerant, V₁, in ft³, and the heat transfer for the process, in Btu. Step 1 * Your answer is incorrect. Determine the initial volume of the refrigerant, V₁, in ft³. V₁= 0.105743 ft3
Steam at 3.5 MPa initially has a temperature of 350C. It was then cooled in an isobaric process until all of it was turned into saturated liquid. Solve for the change in enthalpy.
Solve the following problems. Show your correct and complete solution for this problem. Box your final answers and express in two decimal places. Sketch the schematic diagrams. An adiabatic rigid steam tank has expansion valve. Initially, steam is at 1MPa and 350C. Suddenly, the expansion valve was opened until the tank became empty. If the temperature of steam flowing in the expansion valve is 300C, find the pressure in the valve.
determine the value of AB. Water is to be heated from 20°C to 70°C as it flows through a 40 mm internal diameter and 600 mm long tube. The outer surface of the tube is wrapped with electrical wire which acts as an electrical resistance heater. The heater provides uniform heat flux throughout the surface of the tube. The outer surface of the heater is well insulated. At steady state if the system provides hot water at 0.2475 kg/s, determine the power rating of the resistance heater and the inner surface temperature of the pipe at the exit. Р = 990 kg/m³; k = 0.631 W/(m K); c Pr-4.328 = 4180 J/(kg K); v = 0.66 x 10-6 m²/s:
Nitrogen with a mass of 3.82 kg expands at constant pressure. The initial pressure and temperature in the piston-cylinder system are 172 kPa and 23.4°C, respectively. Because of the heat transfer, the system reached a final temperature of 206.4°C. Compute for the work in kl. Answer in 3 decimal places.
hi, can you solve this ?
A soup is set to boil. When the soup reaches 170°F, remove it from the heat and set it on the kitchen counter. The air in the kitchen is 80°F, and the soup in the bowl is 120°F after two minutes. After removing the soup from the heat, how long will it be 90°F?