Answered: steel plate 2.7 m x 1.3 m x 100 mm…

steel plate 2.7 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling. assume the steel weighs 77.3 kN/cu.m. 1. determine the bearing stress (MPa) in the stee

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ber AB consists of a single C130 x 10.4 steel channel of length 2.5 m. Knowing that the pins A ross…

Q: Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a…

Q: Calculate the maximum tensile and compressive stresses in the section of BC of the beam. 15 ເຄດາ -…

Q: Determine the bearing stress developed in each of the five bolts due to the force P if the diameter…

Q: Three cables having an area of 0.05 in? each is carrying the load W as shown. With no stress, the…

A: Given, A = 0.05 in2 E = 29000 ksi

Q: A frame structure consists of 2” x 2” wood timber and supported by a 10mm dia. cable were build to…

A: We have to determine the maximum normal stresses developed in the structure. Given data :- weight =…

Q: Problem 1. The weight of the crate is 580lb. Calculate the force in cables AB and AC. В 3. 30% A

Q: A plate is fastened to a fixed member by four 20-mm diameter rivets arranged as shown. Compute the…

Q: The vertical links (at BD and two at CE) has an thickness = 9.9 and width = 27.2 mm uniform…

A: bearing stress in BD member load at BD section will be remain 8.5N and diameter of the pin is 7.7 mm…

Q: 1. The beam AB is fixed to the wall and has a uniform weight of 80 lb ft. If the trolley supports a…

A: Hi! Thank you for the question As per the honor code we are allowed to answer only one question at a…

Q: Two angle bars B and C are riveted to bracket A. Knowing that both angle bars are compression and…

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each cable.

A: Given:- 600 lb = m Three cables To find:- Ta,Tb,Tc

Q: Problem 3 Design the diameter of the pin for the hinge support if the allowable shear stress is 250…

Q: A tape of 30 m weighing 0.90 kg has a cross-sectional area of 0.0485cm2. The tape measures 30.00 m.…

A: Given Data: The length of the tape is, L=30 m The weight of the steel tape is, W=0.90 kg The…

Q: 62.5 mm- h Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm…

Q: P Bearing plate Let the allowable stresses in the post be ost=120MPaand oco=6MPA. Compute the…

A: Solution-The given data ,σst=120MPaσco=6MpaModulus of elasticity=200GPa and For concrete 14GPaCross…

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each

Q: A vertical rod is attached at point A to the cast iron hanger shown. The force in the rod is 10…

A: Given : Force in rod is 10 Kips Determine : A) Stresses at point C and D B) The position of…

Q: Q-A hollow shaft of external and internal diameters as 100 mm and 40 mm respectively is transmitting…

A: Given Internal diameter Di = 40 mm Outer Diameter Do =100 mm Number of revolution per minute N = 120…

Q: d help wirh 3 and

Q: 2. The yoke-and-rod connection is subjected to a tensile force of 5 kN. Determine the average shear…

A: The force applied F = 5 kN. The average normal stress in a 40mm diameter rod = 3.98(MPa)The…

Q: An I section girder or stanchion is constructed from two 80mm x 12mm flanges joined by an 80mm x…

A: I section girders: I sections girders are most commonly used in the construction of bridges. These…

Q: A vertical cylindrical, wooden-stave barrel is 3.5 ft in diameter and 5 ft high, and is open at the…

A: Given Dimeter of wooden stave barrel = 3.5 ft Height of wooden stave barrel = 5 ft Specific gravity…

Q: 12.8 The load on the bearing of a cast-iron bracket is 5 kN. The form of the section AB is given.…

Q: The reinforcement steel consists of 5 bars with each having a diameter of 13.75 mm. Take pb=0.425.…

A: diameter= 13.75 mmpb=0.425ymc =1.5yms =1.15NOTE:Since you have posted multiple questions, we will…

Q: Determine (approximately) the force in each truss member of the portal frame. Assume all members of…

Q: A horizontal beam AD with cross-section of 3800 mm² is supported by a wire at C and carries a load…

Q: 2. Assume that a 20mmØ rivet joins the plates that are each 110mm wide. The allowable stresses are…

A: Shear forces acting in parallel with the solid body cause the conversion. As the liquid evaporates,…

Q: A 1 2-inch diameter solid round steel bar must transmit a torque of 6000 in-lb and another moment…

A: If the force can cause the deformation of a material by slippage along the plane or parallel to the…

Q: With

Q: a. Draw the FBD b. Determine the value of P c. Determine the bearing reaction at A. D RA P. E 60° C…

Q: thickness "t" of the steel plate if the

Q: Check the adequacy of the isolated T-beam shown below according to ACI Code requirements and…

Q: "1-80. Determine the maximum allowable torque T that can be transmitted by the joint. The shear pin…

A: Given:- The diameter of the shear pin is 25 mm The failure shear stress of the material (τtail) =…

Q: The beam shown below has a cross section of channel shape with width b-400 mm and height h=80 mm,…

A: Given data:

Question

a steel plate 2.7 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling. assume the steel weighs 77.3 kN/cu.m.

1. determine the bearing stress (MPa) in the steel plate the 18 mm diameter pins exert.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

ASAP
18. A steel loop ABCD of length 1.2 m and of 10-mm diameter is placed as shown around a 24 mm diameter aluminum rod AC. Cables BE and DF, each of 12 mm diameter, are used to apply the load P. Knowing that the ultimate strength of the steel used for the loop and the cables is 400 MPa and that the ultimate strength of the aluminum used for the rod is 220 MPa, determine the largest load P that can be applied if an overall factor of safety of 3 is desired. a. 37.7 KN b. 39.7 KN E С. 74.6 KN d. 45.2 KN B 180 mm 480 mm A 180 mm D
a) The short steel post as shown in Figure 4 is a 152 x 152 UC37 with three compressive loads applied to the top. There is a central load of 200KN and eccentric loads of 'W kN and 100kN. The maximum allowable stress on the face AB is 185 N/mm?. (Area=D47.1cm2,Zxx=273cm) What is the value of the load 'W in kN? WkN A. 152 x 152 UC37 100mm -200KN 50mm 100KN Not to scale Figure 4
The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the smallest safe area of each cable if the working stress is 18 000 psi for steel. 2ft 1.5 ft a. 0.075 in? c. 0.100 in? d. 0.050 in? 5ft b. 0.128 in? Ans:
a.what is the maximum bending stress fbx (MPa) in the girder b.determine the maximum bending stress fby (MPa) in the girder c.using interaction formula fbx/Fbx + fby/Fby
Hand written and clean solution please
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
Calculate the maximum moment (with diagram) & maximum shear (with diagram)
2 - please provide a clear and complete solution, thanks!
DETERMINE THE CONCRETE AND STEEL STRESS AT THE FIXED SUPPORT C.
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.