Shaft a in the figure rotates at 450 rev/ min in the direction shown. Find the speed and direction of rotation of shaft d.

Q: The disk rotates with the angular motion shown. The peg at B is fixed to the disk. Suppose that w =…

A: Given Data The angular velocity is:ω=5 rad/s The angular acceleration is:α=10 rad/s2 The center…

Q: Q3:- The Fig. below shows an epicyclic gear train in which the gear D is held stationary by shaft A…

A:

Q: On two solid discs A and B are available at rest apply equal torques. Yes the moment of inertia of A…

A:

Q: For the electric saw shown in the figure, the saw can slide left and right on the horizontal bed…

A: Displacement of an object is defined as the shortest possible change in the position of an object in…

Q: In the mechanism shown in figure, link 3 is fixed on slider B so it is exactly perpendicular to link…

A:

Q: The drawing represents a planetary reduction gear used in aeronautics. Calculate the speed of the…

A: Speed of motor: N3=1200 rpm and considering N1=0 (is fixed) Number of teeth: Z1=50 teethZ2=18…

Q: he horizontal motion of the spring-loaded follower E, which is always in contact with the cam A is…

A: Velocity is the forward motion of a body. It is equal to the distance covered by the body per unit…

Q: In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular…

A:

Q: Give me right solution with clear calculations.  The figure shows the mechanism, where the bar AB…

A:

Q: Link 4 moves to the right with constant velocity of 75 ft/s. Using the graphical method, find VB,…

A:

Q: below. The cam is rof nt P lying 5 mm away 5 20 mm The distance wost positions of the f

A:

Q: Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels…

A:

Q: The gear is connected to Rack C in the picture shown below. The rope B is attached to the gear at…

A: given:

Q: The slender-bar assembly B (Figure 4) has a mass per unit length of 5 kg/m and is mounted on the…

A: Write the given data with suitable variables: M=0.5t Nmm=5 kg/mt= 3s

Q: The speed of the shaft increases from 65 to 120 rev/minute while turning through 35 complete…

A:

Q: Bar AB is rotating about A with an angular velocity of wAB 2 rad/s counterclockwise. At this instant…

A: Angular Velocity:- Angular velocity is nothing but the rate at which the link rotates around the…

Q: in 4 horizontal directions, in 6 vertical directions is moving. θ2 (⁰) = 20⁰         ω2 = 75 rad/s…

A:

Q: Link 4 moves to the right with constant velocity of 75 ft/s. Using the graphical method, find VB, VG…

A: Note: Dear User! As per Bartleby guidelines, we are allowed to answer only a single question when…

Q: The rotor in the figure turning I and II formed in the beds imbalances and their angles are saving:…

A:

Q: A gear rotating at a clockwise speed of 200 rev/min is subjected to a torque which gives it a…

A: Given information: The initial velocity of the gear = N1 = 200 rev/minThe initial angular velocity…

Q: FOR FIG REFER ATTACHED FILE The shaft is massless. A thin attached triangular mass ‘m’ is mounted…

A: Given, Mass of the triangular lamina - m kg Rotational speed of the shaft - ω rad/s

Q: A cam has the following characteristics: (a) It starts from dwell and ends in another dwell (b) In…

A: In this problem, we have to write the non-dimensional boundary conditions.

Q: The rod AC can move frictionlessly through the sleeve B. The sleeve C travels frictionlessly along…

A: Since the horizontal velocity vc remains constant, the acceleration of the system becomes zero.…

Q: For the compound planetary gear train shown, find the absolute angular velocity of the ring gear.…

A:

Q: A piston is driven by a crankshaft as shown. The crank arm (member AB) has a length of r₁ = 0.60 in…

A:

Q: A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and…

A: The radius of gear A is The initial angular speed of gear A is The final angular speed of gear A is…

Q: A 500 pound weight is attached to a cable that is being lifted by a 10 inch diameter drum.  The 48V…

A: GIven data: The diameter of the drum is d=10 in The weight attached to the cable is Ft=500 lb The…

Q: In the figure shown, If ve=500 mm/s, solve for the (a) velocity (in m/n) of D and (b) the angular…

A:

Q: Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is…

A:

Q: Two cylinders rolling in the same direction has a speed ratio of 4.2. If the diameter of the driven…

A: Hgf

Q: The mechanism in the figure has two toothed wheels and transmits movement by means of a chain. The…

A: Approach to solving the question:Please see attached photos for detailed solutions. Thank…

Q: 3. For the planetary gear set shown, N2 = 10, N4 = 12, N; = 24 and N6 = 50. If w2 = 1, CCWand we =…

A: N2=10N4=12 N5=24N6=50ω2= 1 radsec CCWω6=1 radsec CW

Q: ) It starts from dwell and ends in am p) In section I the cam has a paraboli =) In section I from 0…

A: For the first section the cam has the parabolic profile as,Y=Aγ2+Bγ+C........0<γ<12The…

Q: rotates at 42 rad/s CCw. And all forces acting. D EA - 0.55" AB - 2.5" 0.75"

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.