s relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be supplied to the fluid so that the mineral oil, which is s, can flow continuously with a flow rate of 10.8 m3/h through a horizontal stainless steel pipe with a length of 50 m and a diameter of 40 mm. The roughness value of stainless steel ε= 0.002

s relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be supplied to the fluid so that the mineral oil, which is s, can flow continuously with a flow rate of 10.8 m3/h through a horizontal stainless steel pipe with a length of 50 m and a diameter of 40 mm. The roughness value of stainless steel ε= 0.002

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Natural gas, which is essentially methane is being pumped through a 1m ID steel pipe for a distance of 100 km at a rate of 2 kmol/s. It can be assumed that the flow is isothermal at 289 K. The pressure at the end of the line is 170 kPa. Assuming that the viscosity of the gas is 1.08963x10-5 Pa-s, calculate the pressure (kPa) at the pump discharge.
Fluid with a density of 800 kg/m^3 and velocity of 9.375 m/sec flows through a pipe diameter of 20 mm pipe. Determine the entry length if the viscosity of the fluid is 0.015 kg/(m-sec)? 0.2 m 500 m 0.5 m 0.8 m 20 m Mass flow rate is equal to....
Question 2A large vat contains water, which contains a drainage pipe at a height h1, as shown infigure 2. The drainage pipe has a length L. = 0.4 m, and a radius R = 15 mm, and releaseswater to the atmosphere at a flow rate Q. The connection between the pipe and the vatwall has a loss coefficient of KL = 0.8.Point A is in the middle of the tank at a height, hi.You can assume that the flow in the drainage pipe is fully developed and laminar. The density of water is p = 1000 kg/m° and the viscosity is u = 1 mPa.s. The acceleration due to gravity is 9.81 m/s? a) Find an expression for the pressure at point A.b) Find an expression in terms of Q, L, d, K, p and u for the pressure losses along the pipe (including the losses at the inlet and exit).c) If the flowrate out of the drainage tank is Q = 50 L/min, find ho. You may assumeany change of ho with time is negligible.
Water enters a piping system with a diameter of 0.1016 m from a reservoir with a volumetric flow rate of 0.1893 m³/min. Determine whether the flow is laminar or turbulent if, during the winter, the dynamic viscosities of μ = 1.308x 10-3 Pa 's and 0.687x10-3 Pa s during the summer. What is the length of pipe necessary to reach a fully developed flow?
A horizontal smooth-walled cylindrical pipe has diameter 0.04 m. Water flows along the pipe with a flow rate of Q 2 x 10-4 m³ s-¹. = For water, take the kinematic viscosity as v = 10-6 m² s¹ and the 10³ kg m-³. density as p = (a) Calculate the Reynolds number and establish whether the flow is turbulent or not. (b) Show that λ = 0.035 is a good approximation of the Darcy friction factor for this flow. (c) Calculate the shear stress at the wall of the pipe, and hence find the magnitude of the drag force exerted by the water on a length 2 m of the pipe. L =
Water (specific gravity, G, is 1.0 and the kinematic viscosity, ν, is 1.14 *10-6 m2 /s) flows through a piping system with a flow rate of 0.9 m3/s. The pipe is 2800 m long and 600 mm inside diameter. The pipe has three gate valves, two globe valves, one swing check valve, three standard teesthrough-branch, and four 90o standard elbows. Calculate the following:a- The total length of that piping system.b- Is the flow laminar or turbulent?
Calculate the average and maximum velocities of a fluid flowing at the rate of 20 L/min through a 1 1/2 in. sanitary pipe. The fluid has a density of 1030kg/m3 and a viscosity of 50 centipoises. Is the flow laminar or turbulent?
Kindly solve with full solution and explain. Thank you very much