11.29 (B/C). A state of two-dimensional plane stress on an element of material can be represented by theprincipal stresses o, and o, (o, > 2). The strain energy can be expressed in terms of the strain energy per unitvolume. Then:(a) working from first principles show that the strain energy per unit volume is given by the expression1(o}+o}-2va, o2)2Efor a material which follows Hooke's law where E denotes Young's modulus and v denotes Poisson's ratio,and(b) by considering the relations between each of o,,o,Ty respectively and the principal stresses, where x and y aretwo other mutually perpendicular axes in the same plane, show that the expression1[o+o-2vo,o, + 2(1+ v)r,]2Eis identical with the expression given above.[City U.]

Answered: Image /qna-images/answer/7e462f1e-59b8-4cad-8467-c313170d9776.jpg

rincipal stresses o, and o, (o, > 02). The strain energy can be expressed in terms of the strain energy per unit rolume. Then: (a) working from first principles show that the strain energy per unit volume is given by the expression 1 (o}+o}-2va, 2E for a material which follows Hooke's law where E denotes Young's modulus and v denotes Poisson's ratio, and (b) by considering the relations between each of o,, o, Ty respectively and the principal stresses, where x and y are two other mutually perpendicular axes in the same plane, show that the expression 1 [o+o;-2vo,0, + 2(1+ v)r,] 2E

rincipal stresses o, and o, (o, > 02). The strain energy can be expressed in terms of the strain energy per unit rolume. Then: (a) working from first principles show that the strain energy per unit volume is given by the expression 1 (o}+o}-2va, 2E for a material which follows Hooke's law where E denotes Young's modulus and v denotes Poisson's ratio, and (b) by considering the relations between each of o,, o, Ty respectively and the principal stresses, where x and y are two other mutually perpendicular axes in the same plane, show that the expression 1 [o+o;-2vo,0, + 2(1+ v)r,] 2E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0x10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 270 mm, a cross-sectional area of A = 13520 mm², and a length of L = 4.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1830 με. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. P Answer: Δd = i d eTextbook and Media Save for Later L mm Attempts: 0 of 5 used Submit Answer
This course EHide blocks If a rubber material is deformed as shown in the following figure, determine the normal strain along diagonal AC. C 1 mm 2 mm 10 mm A В 10 mm Select one: O 0.0793 O 0.1402 O 0.1281 0.0382 9:15 PM EN 4/15/2021
1.6-7 A wire of length L = 2.5 m and diameter d = 1.6 mm is stretched by tensile forces P = 600 N. The wire is made of a copper alloy having a stress- strain relationship that may be described mathemat- ically by 124,020ɛ 0 s8s 0.03 (o = MPa) 1+ 300ɛ in which e is nondimensional and o has units of MPa. (a) Construct a stress-strain diagram for the material. (b) Determine the elongation of the wire due to the forces P. (c) If the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
2.5
Determine modulus of toughness in mpa
A rigid steel bar ABC is supported by threerods made of steel [E=200 GPa]. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is 1,200 µɛ. اسوزن Jago 1,500 mm (a) Determine the axial strain in rod (2). (b) The normal stress in rods (1) and (2). 900 mm (1) (2) (2)
Learning Goal: A material is homogenous and isotropic when it has a modulus of elasticity that does not vary with direction and it has uniform properties throughout. When a point in a material is subjected to only normal stresses in three dimensions, but they are not necessarily equal, the state is called triaxial stress. When the response of the material is linear elastic, the strains along the three axes can be calculated using a generalized form of Hooke's law. Each strain depends on all three stresses because of the Poisson effect. €1 Figure 1 [0₂ - V (O₂ +0₂)] a 1 of 1 A cube is subjected to stresses with magnitudes a = 16 MPa, b = 26 MPa, and c = 5 MPa (Figure 1). What is the strain in the y-direction? Let E = 200 GPa and v= 0.26. Express your answer to three significant figures. ► View Available Hint(s) Submit VE ΑΣΦ Part B - Change in volume f change in volume = vec The cube from Part A originally has side length 3.2 cm . What is the change in volume of the cube under the given…
Young's modulus of elasticity and Poisson's ratio of a material are 1.25 x 105 MPa and 0.34 respectively. The modulus of rigidity of the material is: (a) 0.4025 x 105 MPa (c) 0.8375 x 105 MPa (b) 0.4664 x 105 MPa (d) 0.9469 x 105 MPa
Rigid bar ABCD is loaded and supported. Steel [E=30,000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.625 in.2 and bar (2) has a cross-sectional area of 1.25 in. 2. After load P is applied, the strain in bar (2) is found to be 900 με. If there is a clearance of 0.05 in. in the pin connection at C, determine: (a) the stresses in bars (1) and (2).(b) the vertical deflection of point D.(c) the load P.