Question 8 Answers:Equation of line: y =x-axis: x = iy-axis: y = iimmX +im For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates ofthe points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5.Assume F₁ = 45 kN, F2 = 30 kN, F3 = 45 kN, F4 = 25 kN, and M = 115 kN-m.6 m8 mBF.HF₁F₂MDF₁

Answered: Image /qna-images/answer/6c49c7db-fcea-4376-afc6-75664335ec62.jpg

Answered: Question 8

Engineering

Mechanical Engineering

Question 8

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
Pls help with questions no.24
Question 3 10 points V Sav The basic principle to select a material for a product is to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that meet the product performance requirements, and keep the cost of the product as low as possible to use a material with properties that exceed the product performance requirements as much as possible, and keep the cost of the product as low as possible to use a material with properties that meet or exceed the product performance requirements, and keep the cost of the material as low as possible
how did it become 0.1077?
1A
If a critical point at structural element is subjected to the stress shown on the 2D element, determine the factor of safety (FS) against rupture according to the maximum principal stress theory. The material has an ultimate tensile stress Sult = 500 Mpa. 150 Mpa 50 Mpa 250 Mpa
Question 4 The energy collected by a wind turbine is proportional to the wind speed is proportional to the rotor diameter both of the given answers none of the given answers
Can I have the formula for the percent difference?
120 mm 600 mm 10-N 4N 600 mm 4N
Question 1
21 The shear strain in a rod is the deformation per unit length
what will be the pressure gradient (kpa/m) at L=30 cm through the nozzle? At L=0, the liquid flows inside the nozzle has a specific gravity S=10.2, at L=0, the velocity is 2 m/s while at L=70 cm, the velocity is 6 m/s. Assume steady and inviscid flow. The velocity varies linearly with distance through the nozzle. 70 cm L 6 m/s 2 m/s 60 cm Liquid