QUESTION 5) A billboard supported by anchorplate with the help of four rivets to a concretebase as shown in the figure. A uniformlydistributed load of 10 kN/m? acts on the2mB2mrectangulardirection. So then, if the allowable shear stressplate along the perpendicular10 kN/mfor the rivet Tallow=55 MPa and the critical stressthe crushing statedetermine the required rivet diameter that can beused for the safety of system. (Consider theonly shear effect in the solution)forOallow.z=110MPа,3mRivetConcrete baseBase plateBase plateRivet25 mm50 mmConcrete base

Answered: Image /qna-images/answer/fa0a514d-ce7a-4809-a6d8-16fe00d007c8.jpg

QUESTION 5) A billboard supported by anchor plate with the help of four rivets to a concrete base as shown in the figure. A uniformly distributed load of 10 kN/m² acts on the 2m B 2m rectangular plate along the perpendicular direction. So then, if the allowable shear stress 10 kN/m² for the rivet Tallow=55 MPa and the critical stress for the crushing state determine the required rivet diameter that can be used for the safety of system. (Consider the only shear effect in the solution) Oallow.z=110 MPa, 3m Rivet Concrete base Base plate Base plate Rivet 25 mm 50 mim Concrete base

QUESTION 5) A billboard supported by anchor plate with the help of four rivets to a concrete base as shown in the figure. A uniformly distributed load of 10 kN/m² acts on the 2m B 2m rectangular plate along the perpendicular direction. So then, if the allowable shear stress 10 kN/m² for the rivet Tallow=55 MPa and the critical stress for the crushing state determine the required rivet diameter that can be used for the safety of system. (Consider the only shear effect in the solution) Oallow.z=110 MPa, 3m Rivet Concrete base Base plate Base plate Rivet 25 mm 50 mim Concrete base

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem The composite bar system in Figure 4.8 consists of a steel bar and a bronze bar that are both securely attached to a rigid block and rigid supports. The system is loaded with a total load P at the rigid block. If the total applied load P=42000 lb, determine the stresses in the two bars. 6′ S TE FIGURE 1.48 Composite bar system for Problem 12. Steel bar } Rigid block -} Bronze bar E₂ = 30 x 10º psi A₂ = 1 in² E-15 x 10 psi Ag-4 in²
ASAP NEED RIGHT COMPLETE SOLUTION !!!
1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE WEIGHT OF THE WIRE, DTERMINE THE REQURIED 500 Ib DIAMATER IF THE STRESS IS NOT TO EXCEED 20 ksi AND THE TOTAL ELONGATION IS NOT TO EXCEED 0.20 in. ASSUME E = 29 x 106 psi.
A 30 ft tall column has a cross section of 8" x 8" with 1" thick walls, (i.e., it has a 6" x 6" hole in the middle). The material has a Young's Modulus E = 2,000,000 psi, and an axial yield stress of 1600 psi. Using a crushing FOS of 1.67 and a buckling FOS of 1.9, compute the following: a) What is the LARGEST axial load this column can sustain? Hetion b) If the column is braced (in both directions) at 10 feet above the ground, what is the maximum axial load the column can sustain?
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. Determine the following: a. maximum value of w without exceeding the permissible flexure stress of 10MPa. b. maximum value of w without exceeding the permissible shear stress of 1.2MPa. c. maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.Please show your clean and complete solution. Thanks
Answer the questions given the following stresses: d) The value of the shear stress at any plane inclined at any angle with the horizontal is e) The value of the normal stress at any plane inclined at any angle with the horizontal is
In the discussion of Von-Mises criterion, how different is the description of J2 when compared to the Von-Mises stress?
A reinforced concrete beam experiences a load as shown. It has a base of 350 mm, and an effective depth of 600 mm, with 4 – 25 mm diameter rebars. The concrete has a compressive strength of 27.6 MPa, Determine the maximum distributed load that the beam can carry. Assume that the allowable stress in steel is 167 MPa (instead of 160 MPa). w 1.5 m 10 kN 1.5 m 5 m
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :