QUESTION 5) A billboard supported by anchorplate with the help of four rivets to a concretebase as shown in the figure. A uniformlydistributed load of 10 kN/m² acts on the2mB2mrectangular plate along the perpendiculardirection. So then, if the allowable shear stress10 kN/m'for the rivet tallow=55 MPa and the critical stressfor the crushing state Gallow,=110 MPa,determine the required rivet diameter that can beused for the safety of system. (Consider theonly shear effect in the solution)3mRivet*Concrete baseBase plateBase plateRivet25 mm50 mmConcrete base

The force of shear is a sensitive force on the surface. It's said to be the bending moment the…

QUESTION 5) A billboard supported by anchor plate with the help of four rivets to a concrete base as shown in the figure. A uniformly distributed load of 10 kN/m² acts on the rectangular plate along the perpendicular direction. So then, if the allowable shear stress for the rivet tallow=55 MPa and the critical stress for the crushing state Gallow,=110 MPa, determine the required rivet diameter that can be used for the safety of system. (Consider the only shear effect in the solution)

QUESTION 5) A billboard supported by anchor plate with the help of four rivets to a concrete base as shown in the figure. A uniformly distributed load of 10 kN/m² acts on the rectangular plate along the perpendicular direction. So then, if the allowable shear stress for the rivet tallow=55 MPa and the critical stress for the crushing state Gallow,=110 MPa, determine the required rivet diameter that can be used for the safety of system. (Consider the only shear effect in the solution)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the shear stress on the a-a plane. 45 MPa 30° a (а) -10.5 МРа (b) 10.5 MPа (c) -50.3 МРа…

A: Shear stress on plane a-a is given by ζxy'=σy-σx2sin2θ+ζxycos2θwhere θ=angle of inclination of…

Q: 4N20 450 mm 390 mm 300 mm

Q: A cylindrical block is 35 cm long and has a circular cross-section 10 cm in điameter. It caries a…

A: Solved below

Q: Situation #3: A steel wire 12m long, hanging vertically supports a tensile load of 2 kN. Determine…

A: Length of steel wire (L) = 12m Vertically supports a load of (P) = 2kN = 2000N Stress = 140Mpa = 140…

Q: Give the formula for the extreme stresses in the mid-section of axially loaded column. a)…

Q: Determine the largest (allowable) compressive loadP (in kN) that can be supported by the aluminum…

A: Diameter of cyinder, D =200mmangle of plane aa with horizontal =25°Load applied =PFactor of safety,…

Q: A steel circular bar (the yield stress oy = 350 MPa) with diameter d = 60mm is acted upon by bined…

A: M= 3.6x10^3 KN-mm or 3.6 KN-m

Q: A timber beam is 100 mm wide and 150 mm deep. The beam is simply supported and carries a central…

A: Width of the timber beam =100 mm, Depth=150 mm, Central concentrated load of the Simply supported…

Q: At a point on a steel part of landing gear (E = 200 GPa, v = 0.3, Oy = 225 MPa) subjected to a plane…

A: Given Data: 60 degree Strain rosette εa=1200×10-6εb=-650×10-6εc=550×10-6E=200GPaμ=0.3σy=225 MPa

Q: Question 1 q L Figure Q1 A simply supported beam of a rectangular cross-section of width w= 30 mm…

Q: Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 50*10 deep…

A: We have to find the value of depth of uniform stress block

Q: 5. A reinforced concrete beam has a width of 300 mm, an effective depth of 500 mm and is reinforced…

Q: d) What is the maximum in-plane shear stress and the angle of its associated plane? What are the…

A: Given, To determine, d) The maximum In-plane shear stress and the angle of its associated plane and…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a rigid base and confined in x-coordinate direction between two rigid end plate. If the upper face of the center cube B is subjected to uniform compressive stress of 0.5 kN/mm², compute for cube B, the following: (i) The direct stress in x-direction (₂) (ii) The direct strains in the three coordinates directions x, y and z (iii) The volumetric strain Rigid A E=150 kN/mm² μ = 0.25 o₂ = 0.5 kN/mm² B E = 200 kN/mm² μ = 0.3 -Rigid C E = 150 kN/mm² μ = 0.25 Rigid
The concrete post is reinforced using six steel reiforcing rods, each having a diameter of 20 mm. Determine the stress in the concrete and the steel if the post is subjected to an axial load of 900 KN. Assume that E = 200 GPa for steel, and E= 25 GPa for concrete 900 KN 250 mm 375 mm stress in steel = 65.3 MPa and stress in concrete = 6.4 MPa stress in steel = 67.3 MPa and stress in concrete = 8.4 MPa stress in steel = 69.3 MPa and stress in concrete = 10.4 MPa stress in steel = 71.3 MPa and stress in concrete = 12.4 MPa O
A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around a solid steel shaft. The shrinking allowance is 1 part per 1000. Neglecting shaft expansion, determine: (a) The stress in the system at standstill. (b) The speed at which the shrink fit will loosen as a result of rotation. Material density is 7800 kg/m³; Poisson's ratio is 0.3; Young's Modulus is 210 GPa; [108.68 MPa: 4300 rpm
A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter) Pay attention to units, and calculate your answer to one decimal place.
Q5) The wooden block shown in Figure (4) will fail if the shear stress acting along the grain is (3.85 MPa). If the normal stress (d, = 2.8 MPa), determine the necessary compressive stress (a) that will cause failure. Figure (4)
1) A box beam has the following dimensions: h = 500 mm, b = 180 mm, and t = 22 mm. If the yield stress is 270 MPa, what is the yield moment? (Express your answer in kN-m, up to 1 decimal place) 2) A box beam has the following dimensions: h = 500 mm, b = 180 mm, and t = 22 mm. If the yield stress is 270 MPa, what is the shape factor? (Express your answer up to 1 decimal place)
Part A Determine average normal stress. (Figure 1) Express your answer with the appropriate units. Javg = Part B μA Submit Request Answer Value σ1,02= 20 MPa IVD ΑΣΦ11 Units vec ww Determine the principal stress. Enter your answers numerically separated by a comma. ? 80 MPa 30 MPa www MPa
1) A brass pipe with a 0.5inch inside diameter and 1/16 inch wall is twisted using a 14inch long pipe wrench. If a load of 74 lbs is applied perpendicularly to the end of the wrench. If the E of brass is 14.6x10^6 psi, what is the max torsion stress in the pipe? • Find the outside diameter of the pipe using the ID and given wall thickness. • Find the polar moment of inertia of the cross-section of the pipe. • Find the torque being applied to the pipe, via the wrench. • Use the torsional stress equation to find the requested stress. Compare your answer: Max Torsional Stress 36.61 ksi
Answer the questions given the following stresses: d) The value of the shear stress at any plane inclined at any angle with the horizontal is e) The value of the normal stress at any plane inclined at any angle with the horizontal is
A prestressed concrete beam of rectangular section 300mm wide and 600mm deep is prestressed by 5 pieces of 8mm high tensile wires at 500mm from the top and 15 pieces of 8mm diameter high tensile wires at 83 mm from the bottom. The initial stress in the wires is 1200 MPa. Estimate the loss of stress in the bottom wires due to elastic shortening of concrete. Assume modular ratio = 6.