Question 4 a. A solid circular L shaped ABC structure is built in at one end and is point loaded at the other end as in Figure Q4a. Find the total main elastic energy inside the structure due to the 50 N lateral load. (Given E 200 GPa, v= 0.3, Diameter = 80 mm) B SOMMAR 3m 2m 50N с Figure Q4 UTM NIKA

Question 4 a. A solid circular L shaped ABC structure is built in at one end and is point loaded at the other end as in Figure Q4a. Find the total main elastic energy inside the structure due to the 50 N lateral load. (Given E 200 GPa, v= 0.3, Diameter = 80 mm) B SOMMAR 3m 2m 50N с Figure Q4 UTM NIKA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
A column, pinned at top and bottom, is made up of two C 10 x 25 steel shapes (see figure) that act together. Gap- 26 ft. Note that distance d is measured between the centroids of the two C sha ve this problem using the assumptions of ideal, Assume that E = 30,000 ksi and L slender, prismatic, and linearly elastic columns (Euler buckling).) (a) Find the buckling load (in kips) if the gap is zero. 37.3 kips (b) Find required separation distance d (in inches) so that the buckling load is the same in y and z directions. 6.92 in.
5
Rijit 1,2 m 0,6 m- 1 m Çap:50 mm The system in the figure is carried by a 50 mm diameter column. If the modulus of elasticity of the column is 70 GPa, find the maximum load q that the column can carry.
The rigid bar ABC is supported by pin at A and aluminium wire BD, is horizontal before the Load P is applied. Find the vertical displacement of point C caused by the load P=35 KN. Where E = 70 GPa and the area of the wire is 200 mm?. D. 300 mm B 400 mm- 200 mm
250 mm 60 350 mm For the pin at point O in the above figure the load it can safely carry is 5 kN. In this case 120 the maximum L that the angled elbow element AOB can carry find the charge and the reaction force at point B also O and at the middle of the B points. Calculate the incoming cross section effects.
Q6/ For the following carbon fiber foot in the figure below, the foot length to the ankle joint is 25cm, foot average width is 8cm, foot average height is 1cm, if the foot modules of elasticity is 270Gpa, determine the foot tip deflection if the patient is walking at the (toe off) position as shown in figure. Assume the reaction force is 800N. 3-3
A beam weighing 50 kg is attached to a pin at C and supported by a steel cable OA with Young's modulus, E= 200 x 10° N/m2 as shown in Figure Q2. An inclined force of 5000 N is applied to end of the beam at point D with 40° angle measured from the x-Axis. 5000 N Sna pho Wel 2.5 m B. 888-888- 4m By providing your a automateditext mer messaging eates may 5 m 3 m Figure Q2 Loadings on beam My Textbo a) Draw a free-body diagram of the beam Solunons b) Calculate the tension of steel cable OA c) Determine the reaction forces of Fex and Fey d) Determine the elongation of steel cable OA byChego
A torsional moment T = 5,382 Nm and a load P = 55,253 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q5. The load P is offset from the centre of the circular cross-section by a distance e = 6 mm. The shaft has an inner diameter d = 43 mm and an outer diameter D = 97 mm. Point A in Figure Q5 is on the outer surface of the shaft. Figure 5 Calculate the direct (or normal) stress in the x-direction σx at point A (the 'x-direction' is along the longitudinal axis of the shaft, along its length L). Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.
(a) Calculate the total elastic strain energy stored in the material of the pin-jointed structure shown in Figure Q4(a). The structural members cach has a cross sectional area A, elastic modulus E, shear modulus G, moment of inertia I and polar moment of inertia J. B L. A 45 30 Figure Q4(a) (b) An elastic structure with flexural stiffness El is pinned at A and fitted with a roller at end C, as illustrated in Figure Q4(b). The structure carries a uniformly distributed load w (force per unit length) on member AB. (i) Determine the reaction at the roller support C, in terms of w and R. Using Castigliano's energy theorem, determine the horizontal displacement of end C of the structure. Consider bending effecis only. R Figure Q4(b)