Question 3. 120 mm diameter and 600 mm long copper material will be produced by direct extrusion process as follows. Strength coefficient for copper is 300 MPa and plyumization base The pattern angle constants are 0.5. Accordingly, it is not the case. a) The rate of extrusion, b) The shape factor, c) While the remaining material in the cylinder is 500 mm, the force required to ensure the forward movement of the ram during extrusion, d) At the end of the process, if the volume of the last part of the cylinder is 0.4 dm find the length of the extruded part. 2,7 mm 55 mm

Question 3. 120 mm diameter and 600 mm long copper material will be produced by direct extrusion process as follows. Strength coefficient for copper is 300 MPa and plyumization base The pattern angle constants are 0.5. Accordingly, it is not the case. a) The rate of extrusion, b) The shape factor, c) While the remaining material in the cylinder is 500 mm, the force required to ensure the forward movement of the ram during extrusion, d) At the end of the process, if the volume of the last part of the cylinder is 0.4 dm find the length of the extruded part. 2,7 mm 55 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Must be detailed responses Question : Provide a precise definition of the cross-product. And give an explanation of how it relates to moments of forces.
8. Design Problem: A material is needed to support a hanging sculpture with an overall tensile load of 800 N. It is important that the material not undergo any permanent deformation under this load and must have minimum volume/diameter. Using a circular rod, design structural components using your data for each of the three materials. Which material would you choose for the application and why? If the requirement was minimum weight, rather than minimum volume, which material would you use? Show sample calculations.
Q3: In drawing of circular rod, it is required to perform 15% reduction in cross sectional area through a tapered die. Estimate a die angle in order to assure at least 80% homogeneous deformation in produced part and then compare the current process efficiency with ideal deformation? Take C-1.08 and C-0.45.
What are the principal strains?
Home Work: Show that the true strain rate in extruding a round billet of radius ro as a function of distance x from the entry of a conical die can be given as: 2V,rž tana where; Vo: ram velocity (ro-xtana)3
Please please please l need the answer.
An annealed copper strip 9 in wide having .2 K=80,000 psi, N=0.60, and a height of 1 in _was flat rolled to a height of 0.90 in with 12 in roller radius rotating at 120 rpm a) Calculate the force and the power .needed to operate this Process
Stick-slip phenomenon results in extrusion defect.
3
elongation. 6) Chapter 3: Problem 3.7: (USCS Units) The flow curve for a certain metal has a strain-hardening exponent-0.20, and its strength coefficient=26,000 lb/in2. Determine (a) flow stress at a true strain= 0.15 and (b) true strain at a flow stress = 20,000 lb/in2. (c) What is the likely metal in this problem? %3D
6) Chapter 3: Problem 3.7: (USCS Units) The flow curve for a cestain metal has a strain-hardening exponent=0.20, and its strength coefficient-26,000 lb/in2. Determine (a) flow stress at a true strain= 0.15 and (b) true strain at a flow stress = 20,000 lb/in2. (c) What is the likely metal in this problem?
Q3 Give the reason for 10 of the following. - 1- The use of lubricant in wire drawing die. 2- The uses of tungsten carbide for the manufacturing of die tool. 3- The increase of Mo/Si ratio during the production of white cast iron. 4- The addition of Al to copper alloys. 5- Aluminum is a better overall conductor than Copper for long distance electric transformation. 6- The addition of cryolite in smelting electrical furnace due to the production of aluminum. 7- The addition of Magnesium and Cerium during the production of Ductile cast iron. 8- The addition of 13% Cr to steel in corrosive environment. 9- The increase of hardness for chips due to the cutting process. 10- The brittle fracture of steel at low temperature lower than -4 C. 11- The heating of metal after the rolling process.