QI: By working stress method calculate the maximum concentrated load (P) at free edge of the cantilever beam (2.5 m) span shows below with the section, the beam carries an uniformly distributed dead load (10 kN/m) (with self-weight) if the unit weight of concrete is 24 kN/m .f'c= 22 MPa and fy= 400 MPa. 3 25mm 50% 150 200 mm 150

QI: By working stress method calculate the maximum concentrated load (P) at free edge of the cantilever beam (2.5 m) span shows below with the section, the beam carries an uniformly distributed dead load (10 kN/m) (with self-weight) if the unit weight of concrete is 24 kN/m .f'c= 22 MPa and fy= 400 MPa. 3 25mm 50% 150 200 mm 150

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 1) F=11 kN single load, M=22 kN.m moment andA distributed load of w=5 kN/m is effective. The length L is also given as L=5 m.The cross-sectional properties of the beam are; body height Hg=218 mm, body thickness xg=18 mm, flangewidth xf=190 mm, flange height yF13 mm. Point E on the section is flange-It is located just below the body junction. In the section taken from the B line of the beamIt is desired to determine the stress state. According to this;Question 1-A) Find the support response (DY) at point D. (Return your result in kNQuestion 1-B) Find the support response (Ay) at point A. (Return your result in kNwrite.)Question 1-C) Find the shear force (VB) at point B. (KN your resulttype in size.)
A beam is of T section, as shown in fig. The beam is simply supported over a span of 4m and carries a UDL of (1.7+32.) kN/m run over the entire span. Determine the maximum tensile and maximum compressive stress
H. w O P = 2 KN So mm For Simply supported beam shoun, determine the value of strusses develuped on it. what type f strees is result from loading? calculate the stress for di do d= 25 di = 15 do = 25 mm m tw. Seetions @ solid @ hollas
HOMEWORK: Q1/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa and the compression stress 70MPA. Find the maximum value of load P 50mm はomm W=2.5p Kw/m 300 Im tan 4m lom ww 150mm Q2/ A beam has a cross section as shown below with unknown dimensions of the flange (b,) and the web (b,) and is subject to a maximum positive moment at the center which causes a tensile stresses at points A and B of 900N/cm2 and 600 N/cm? respectively ba 10 J00KN 50 Cm sm 200cm
1
Ql: An I-section shown in Fig. is simply supported over a span of 15 m. If the maximum permissible bending stress is 90 N/mm?, what concentrated load can be carried at a distance of 5 m from one support? 100 mm 11.5 mm V 7.5 mm W 225 mm N. A B 5m. 15 m 11.5 mn
Please solve this question again. I think previous solution was incorrect
Picture given below; There is a uniformly distributed load on the beam, which is made of Al2010 (T4) alloy T-profile and is connected to the "A" sliding bearing with "B" joint fixed support. Safe compression and tensile normal stress of the beam is Gemn=100 MPa. q=23 kN/m C-C Kesiti + 15 | 18 | 15 q=23 kN/m A유 30 cm 100 cm 150 cm 16 KİRİŞ T- PROFİLİ 74 Ød MAFSAL PİMİ Ölçüler mm dir. 104 S-1) Calculate the support reactions by drawing the SCD of the beam. S-2) The beam; a) Draw the shear force diagram, b) Moment diagram and determine the maximum moment. S-3) Find the x and y axis coordinates of the center of gravity of the cross-sectional area of the beam whose T-profile dimensions are given. S-4) Find the moments of inertia with respect to the vertical and horizontal axes passing through the center of gravity of the T-profile cross-section area. S-5) Find the tensile and compression stresses caused by bending on the beam with T-profile and check the safe carrying condition of this…
A simply supported beam is subjected to a distributed load of wi=640 N/m and a point load pi = 940 N. Calculate the internal loadings on the cross section at C. %3D D 1. 3. 6. The internal normal load at C is N = 1280 X N. The internal shear load at C is V = 242 XN. The internal bending moment at C is M = 476 o N-m.
1 B) Calculate the deflection and rotation at point (a) for the beam showing in figure by using unit load method. (E = 200*10° kN/m2, I = 3.125*10³ m*). 30 kN 6 KN/m a 2 2m 3m
Show COMPLETE SOLUTIONS Draw FBD
4. The properties of the steel-reinforced concrete beam are b =8 in., d=18 in., The total area of the steel-reinforcements is Ast = 1.25 in.?, Est/Eco= 6, and the yield stress for steel-reinforcement is (Ost) yp =60000psi. (a) Determine the bending stress that would cause the reinforcement to yield. (b) Compute the corresponding maximum stress in the concrete. h – NA d Ag (total area)