Q/Complete the dam section dimensions and then find the moment of allconsidered forces about the toe? Take C=0.6,325 KN/m, S̟ = 2.4, H = 9 m. H-78KNY. = 10-, Y, =%3D%3D%3DH, = 2a/5, – CF.bHiWw1Fsh2FsysPEWw3FsvW2FshWwa/FshWib=9 mC. Yw.H'C. Yw.HTusCY,H' + (C. Yw. H – C. Yw. H')

Given: Yw= 10kN /m^3 Yc = 25kN/m^3 Ss = 2.4 C = 0.6 H = 78

Q/Complete the dam section dimensions and then find the moment of all considered forces about the toe? Take C=0.6, KN 3. 10-4 Y 25 KN/m, S = 2.4, H = 9 m. H=78 %3D %3D %3D 31 H, = 2a/5,- c %3D F.b Hi Fsv Wwi Fsh2 Fsys PE Ww3 Fsv W2 Fsh Wway Fsh, W, Wi b=9 m C. Yw.H' C. Yw.H CY,H' + (C. Yw. H - C. Yw. H')

Q/Complete the dam section dimensions and then find the moment of all considered forces about the toe? Take C=0.6, KN 3. 10-4 Y 25 KN/m, S = 2.4, H = 9 m. H=78 %3D %3D %3D 31 H, = 2a/5,- c %3D F.b Hi Fsv Wwi Fsh2 Fsys PE Ww3 Fsv W2 Fsh Wway Fsh, W, Wi b=9 m C. Yw.H' C. Yw.H CY,H' + (C. Yw. H - C. Yw. H')

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the design shear strength of the given shape, using Fy-50 ksi. Blank 1 W14x53 A = 15.60 in ^2 ... 13.900 in. tw = 0.370 in. bf = 8.060 in. tf = 0.660 in. 10-7/8 in. 1.2500 in. k1 = 1.0000 in. gage = 5-1/2 in. rt = 2.150 in d/Af = 2.62 541 00 in.^4 Sx = 77 80 in 43 5.890 57 70 14 30 in. = XI in 4 Sy | in 3 ry = 1.920 in. Zx = 87.10 in 43 Zy = 22.00 in ^3 J = 1.94 in ^4 Cw 2540 in.^6 a 58 22 in. Wno = 26 70 in.^2 Sw = Qf = 35.50 in ^4 16.80 in.3 Qw: 42.60 in.^3 |||| 11 I|||
I need the answer as soon as possible
100% SURE PLEASE
225 P= 8 P= 10 9,- 18 H3 2 (m) 1 (m) . 4.50 (m) 1.50 (m)
The Channel section is used as a purlin placed on top of trusses with spacing of 4.1 m and slope 1V to 4H. The purling are supporting a total uniform load of 20.2 kN/m.Properties of Channel:Sx = 119 × 10^3 mm^3Sy = 87 × 10^3 mm^3 Compute the maximum bending stress.Use NSCP 2015Round your answer to 2 decimal places.
Stress Analysis of Trusses using method of sections. pls answer within 30 mins
A 2.0 meter Cantilever Beam Carries Direction. The Couple of size and a 386.98 kN-m at Clockwise Prescribed beam properties is b=250mm, d=450mm, d' = 75mm. f'. = 30MPa. The Beam is Reinforced with a Grade 60 Steel with and fy 414.70 MPa. Calculate the Maximum Steel Ratio Calculate the depth if the compression block Calculate the Steel Reinforcement Area at Compression and Tension 386.98 kN-m
3
Determine the maxi mum shear stress deue loped in the beam 5 KN/m Ø4 cm Ø3 cm 3 N/m 0.2 m 0-2m 0.2
slab single /simple spanning slab spanning twoway/ double The timber structure below has a single spanning floor of grade C16 beams of weight 4.2 kN/m? and a two way spanning floor 150 mm thick of CLT flooring of density 410 kg/m3. Dimensions are as follows: Length a = 2.8 m %3D b = 4.4 m C = 4.4 m Find the reaction of the internal beam acting on the edge beam at X. Give your answer in kN to one decimal place. Do not put units in the answer box. The conversion from kg to kN is (x 9.81 / 1000)
Question A1. The doubly reinforced rectangular concrete section shown in Figure A-1 is designed for the hogging moment of a continuous beam. The section has a total depth of D mm, width B= 300 mm and is reinforced with 4N28 bars at the top and 2N28 bars at the bottom. Given: f. = 40 MPa, fay = 500 MPa. Find other required data from AS3600-2018. a) Calculate the beam depth, D where D = 500+20n mm. Take n = 3rd digit of your student number. For example: your student number = 18505679, n = 5; D = (500+ 20*5)=600 mm) Note: Use the calculated D from (a) for the further calculation in (b-c). b) Calculate ultimate moment capacity (Mu) of the section. c) Check ductility of the section according to AS3600-2018. 300 4N28 2N28 Figure A-1