Q2/ Three pipes are connected in series. The physical properties of the pipes are in Table below. If (PA_PB) = 150 (KN/m²), (ZA-ZB)= 5m, p=1000 (Kg/m³), and v=1.02x106 (m²/s). Calculate the flow rate through the system. Neglect the minor losses. Pipe No. Length of pipe Diameter Roughness Coefficient L d (mm) 1 2 3 (m) 100 150 80 80 60 40 0.24 0.12 0.2 e (mm) Relative Roughness (e/d) (Dimensionless) 0.003 0.002 0.005

Q2/ Three pipes are connected in series. The physical properties of the pipes are in Table below. If (PA_PB) = 150 (KN/m²), (ZA-ZB)= 5m, p=1000 (Kg/m³), and v=1.02x106 (m²/s). Calculate the flow rate through the system. Neglect the minor losses. Pipe No. Length of pipe Diameter Roughness Coefficient L d (mm) 1 2 3 (m) 100 150 80 80 60 40 0.24 0.12 0.2 e (mm) Relative Roughness (e/d) (Dimensionless) 0.003 0.002 0.005

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

topic: parallel pipes hydraulics
92 Calaulate the flow rate of the each pipe is given belowi O.120m/s (4) K2=2 (2) Ku=4 (3) (5) Es=5 0.040 m/s O-030 ms The initial value of the flow rate for pipes ore gren as Ri=0.07 /s 92=0.05 m/s 93= 0.01 m% Q4=0,01ms and Q5=0,03 m3
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
len3
Given the following: Diameter of Pipe = 1m, Length of Pipe = 845m and Head loss = 1.01 m, Determine the discharge using Darcy Weisbach, f=0.021. (A) 0.93 cms B) 0.73 cms 0.83 cms 0.63cms
Please answer, hydraulics. Thanks
03. Find the pressure difference between A and В Oil RD = 0.8 Water 0.4m 0.2m 0.3m Water 0.4m 0.4m B (a) 1692 Pa (b) 1913 Pa (c) 2141 Pa (d) 2551 Pa
nat3
Please show all work including unit converstions and please make sure to show all units. For P1=10+(6), so P1=16 psi for P2=20+0, so P2=20 psi for D1= 1ft for D2=0.6ft for Q=5.4 cubic ft per second
At Point A, in a pipeline carrying water (y=62.4 Ib/ft^3) the diameter is 4.0 ft, the pressure is 10 psi, and the velocity 4 ft/s. At point B, 6ft higher than point A, the diameter is 2 ft and the pressure is 2psi.determine the following:(a)quantify the losses in this system and (b) is the flow going from Point A to Point B or from point B to point A. why?
Determine the discharge in pipes 1, pipe 2, pipe 3 and pipe 6 in the system shown if the total head loss from A to B is 100m and friction factor for all pipes is 0.02.