Q10 (a) State in words and in the form of a truth table the actions of the following logic gates. (ii.) OR (iii.) NAND (1.) AND (b.) The figure shows a transistor circuit operating in the common-emitter mode with a current gain of 60 and VRE of 0.7V. 200.0 10 kn 4.5 V Vout 2.7 V VBE Calculate the output voltage Vo-

Q10 (a) State in words and in the form of a truth table the actions of the following logic gates. (ii.) OR (iii.) NAND (1.) AND (b.) The figure shows a transistor circuit operating in the common-emitter mode with a current gain of 60 and VRE of 0.7V. 200.0 10 kn 4.5 V Vout 2.7 V VBE Calculate the output voltage Vo-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6- Design a logic cct using NAND gate and convert BCD code to Excess-3code.
Q1.The single phase full bridge inverter has a resistive load of R= 402 and the de input voltage is Vs-80V. Determine: (a) the rms output voltage at the fundamental frequency1.(b) the output power Po. (c) the average and peak currents of each transistor, (d) the peak reverse blocking voltage of each transistor, (e) the THD, (f) the DF, and (g) The HF and DF of the LOH.
find gate voltage,if gate-cathode characteristics has a slope of 100 and gate power dissipation is 0.9W. a. 8.4V b. 3.4V c. 9.4V d. 4.4V
6. Design a NAND Gate digital circuit using an AND gate and an inverter. Describe the operation of the circuit.
a) A standard TTL inverter gate is shown in the figure. The supply voltage is 5V. Calculate the output voltage for both logic low and logic high input cases assuming input voltages respectively as 0.11V and 4.2V. Br= 130; BR = 0.24. You can make approximations when needed. Br = IcIs active region; BR = IE/ls inverse active region b) Assume you connect a resistor of 1.8K to the output of the circuit when the output is at logic high. What will be the change in the output voltage? 1302 R3 1.6k2 R, 4k2 Input o T, Output T, V, V. IkQ R,
Q1. 220V, 200, 100mH are represents data information for a two-level VvSI feeds an inductive load. If the output frequency of the inverter is 50HZ, calculate: a- Instantaneous load current. b- Average supply current. c- Load rms voltage and current. d- The average and peak transistor and diode currents. e- Sketch the input and the output current waveforms.
**Without Explain Please ****Without Explain Please ****Without Explain Please ** 1. When a press switch is connected to VDD one side and the other to the mid of two resistor as voltage divider which one end to the ground and the other goes to P3 is called.. a.Not activeb.Active highc.Active low 2. In the AVR ATMEGA16 the structure of the IO/p ports includes … a.1 ADCb.8 ADCc.2ADCd.4 ADC 3. The sketch for AVR ATMEGA16 when connected to an LED PORTD |=(0x01<<0) means a.Turn on PC1b.Turn off PC0 1c.Turn on PC0 d.Turn off PC1 4. The sketch for AVR ATMEGA16 statement if((PINC &(0x01<<2))==1) means a.Wait for PINC1 to be logic 1 b.Wait for PINC1 to be logic 0 c.Wait for PINC2 to be logic 0. d.Wait for PINC2 to be logic 1 5. The sketch for AVR ATMEGA16 statement PORTB &=~(0x00<<1)means a.Turn on PB1b.Turn off PB0c.Turn off PB1 d.Turn on PB 0 **Without Explain Please **
5. MOSFET's can be either NMOS or PMOS and can also: a. Glow in the dark b. Come as Enhancement mode or Depletion Mode c. Make a noise when current flows d. Not be used as switches
Resistor Transistor Logic (RTL) circuits Explain( AND,NAND,NOR,OR AND NOT ) below is the link: https://tinyurl.com/2p8fj34c
Mention how NPN and PNP transistor works?